GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 38

GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Скачать руководство пользователя страница 35

8)

Enter the Digits you require the Pager to display (If you
intend to also send a Site Code only the first 13 digits of
this message will be sent to the Pager).

9)

Press YES. The display will show:-

10)

To program the Set Pager 4 digit site code press 6
followed by YES (pressing NO will display the current
Site Code) or go to step 12 to skip this option.
The display will flash showing:-

11)

Enter the Digits you require followed by YES.
The display will show:-

12)

To program the Set Pager message type press 7 followed
by YES (pressing NO will display the current message
type) or go to step 14 to skip this option.
The display will show for example:-

13) Choose

from

1 Send only the Message to the Pager (if programmed)
2 Send only the Site Code (if programmed)
3 Send Both (if programmed)

Enter your required Digit followed by YES.
The display will show:-

14)

To program the Pager Make press 8 followed by YES
(pressing NO will display the current Pager Make) or
go to step 16 to skip this option.
The display will show for example:-

15)

Choose from
1 BT

Easyreach (Default)

2 Vodaphone

Premierline

3 Mercury

Page1 Minicall

Enter your required Digit followed by YES.
The display will show:-

16)

This completes the Pager programming. To escape
press o twice.

PR4100Rev1.7 SD.QXD 07/03/01 16:22 Page 35

«
...
33
34
35
36
37
...
»

Содержание GARDTEC SPEECH DIALLER







































Отзывы:

Нет отзывов