GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 38

GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Скачать руководство пользователя страница 32

11.1

ENGINEER APPENDIX 2

Reset Modes.
Two reset modes are available to the engineer. Mode 1 reset will reset all programmed
settings to factory defaults (including user and engineer codes). Mode 2 will reset the user
and engineer codes.

Reset Mode 1.

1)

Remove all power from the Gardtec Speech Dialler for at least five seconds.

2)

Re-apply power to the unit

3)

Whilst '88' is displayed (the first 8 seconds) Press 4 6 YES NO

4)

The unit will return all programmed settings to factory defaults and re-calibrate
(this may take up to one minute).

Reset Mode 2.

1)

Remove all power from the Gardtec Speech Dialler for at least five seconds.

2)

Re-apply power to the unit

3)

Whilst '88' is displayed (the first 8 seconds) Press 1 9 YES NO

4)

The unit will return user and engineer codes to factory defaults and re-calibrate
(this may take up to one minute).

PR4100Rev1.7 SD.QXD 07/03/01 16:22 Page 32

«
...
30
31
32
33
34
...
»

Содержание GARDTEC SPEECH DIALLER







































Отзывы:

Нет отзывов