GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 38

GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Скачать руководство пользователя страница 19

7.2

PROGRAMMING MESSAGES

Enter the Speech menu (refer to section 7.0)

1)

With the display showing:-

2)

Enter the message option number from the following list

Option 9 Play/Delete/Record Common Message

Option 1 Play/Delete/Record Message 1

Option 2 Play/Delete/Record Message 2

Option 3 Play/Delete/Record Message 3

Option 5 Play Common & message1

Option 6 Play Common & message 2

Option 7 Play Common & message 3

If 1 was entered the display would show:-

3)

Pressing NO will play the message then return to step 1

or

4)

Press YES to delete or program the message (not applicable
to options 5, 6 or 7). The display will flash:-

This is asking if you wish to delete the existing message.

5)

Pressing YES will delete the message and return to step 1

or

6)

Pressing NO will allow the existing message to be
re-programmed. If NO has been pressed the display
will show:-

7)

At this display you should speak your message into the
dialler at a distance of approximately six inches (15cm)

Common message length is eleven seconds, if your message
is shorter than this the recording time it may be terminated
by pressing the 0 key.

PR4100Rev1.7 SD.QXD 07/03/01 16:22 Page 19

«
...
17
18
19
20
21
...
»

Содержание GARDTEC SPEECH DIALLER







































Отзывы:

Нет отзывов