GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 38

GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Скачать руководство пользователя страница 12

Short Message 3
This message corresponds to a trigger 3 input and will be played after the common
message. Speech for short message 3 may be up to 3 seconds duration, a typical
message would be:-

"Burglar Alarm"

Once the speech message(s) have been programmed they may be replayed with or
without the preceding common message

User Options

Change User Code
The user has the option (via the existing user code) to change the user code to any other
four digit number. should the new user code be the same as the engineer code the dialler
will display 'no' and the code will not be updated. The default user code is 5678

Change Dial Attempts
The dialler has a list of up to four telephone numbers, the number of dial attempts is the
number of times it will try to dial these numbers. A successful call will be registered when
the message is passed to the recipient (and acknowledged if required).

This option allows the number of times the dialler will dial the telephone numbers on the
list to be programmed from 1 to 3 times.

Call Acknowledge
Call acknowledge may be programmed to 0, 1, 2, 3 or 4. If 0 is programmed the dialler will
see when it has passed a message to the recipient and the dialler will then shut down. If
programmed to 1, 2, 3 or 4 the dialler will give a tone after the message has been passed,
this tone then has to be acknowledged by the recipient by pressing the # key for 1 second,
the tone will be repeated and will need to be acknowledged again by pressing the # key. If
the acknowledgement is accepted a triple tone will be given and the call will be registered
as successful by the dialler.

This procedure will then be repeated to the other telephone numbers until the desired
number of acknowledgments has been received. The default number of acknowledgments
required is 1.

It is advisable that the total of telephone numbers you have programmed should be at
least equal to the number of acknowledgments programmed.

View Last Call Log
This option allows the user to view the last call log. The log will give information as to the
last telephone number dialled and what message was passed. Information is also stored
concerning failure to communicate and aborted calls. The log is accessed by pressing the
NO key when 'on' or 'oF' is displayed.

PR4100Rev1.7 SD.QXD 07/03/01 16:22 Page 12

«
...
10
11
12
13
14
...
»

Содержание GARDTEC SPEECH DIALLER







































Отзывы:

Нет отзывов