GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 38

GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Скачать руководство пользователя страница 11

5.0

PROGRAMMABLE USER OPTIONS

The dialler is fully programmable, all settings will be retained in the event of the dialler
being down powered. A description of each option is given below:-

Emergency services must not be called with this equipment.

Repeat numbers will not be accepted by the dialler.

Telephone No 1
Any sequence of digits (Max fifteen digits).

Telephone No 2
Any sequence of digits (Max fifteen digits).

Telephone No 3
Any sequence of digits (Max fifteen digits).

Telephone No 4
Any sequence of digits (Max fifteen digits).

The user shall ensure all numbers are correctly entered.

Speech Messages

Common message
When the dialler is triggered and the call is answered the dialler will pass this common
message followed by the short message corresponding to the trigger input. Speech for this
common message may be up to 11 seconds duration, a typical message would be:-

"This is John Atherton 5 High Street Newtown, this is a...."

Short Message 1
This message corresponds to a trigger 1 input and will be played after the common
message. Speech for short message 1 may be up to 3 seconds duration, a typical
message would be:-

"Fire Alarm"

Short Message 2
This message corresponds to a trigger 2 input and will be played after the common
message. Speech for short message 2 may be up to 3 seconds duration, a typical
message would be:-

"Personal Attack"

PR4100Rev1.7 SD.QXD 07/03/01 16:22 Page 11

«
...
9
10
11
12
13
...
»

Содержание GARDTEC SPEECH DIALLER







































Отзывы:

Нет отзывов