GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 38

GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Скачать руководство пользователя страница 34

To program the Pager options proceed as follows

1)

Ensure the Speech Dialler has previously been programmed with
at least one telephone number and a common message
(refer to section 7.0).

2)

With the display showing:-

or

Enter the User Code (5678 default) followed by yes.
The display will show:-

3)

Press 3 followed by YES
The display will show:-

4)

To program the Set Pager to Tel No. Press 4 followed
by YES or go to step 7 to skip this option.
The display will show:-

5)

Enter the Telephone Number you wish to allocate as
a Pager Number (e.g Tel No. 1, 2, 3 or 4).

If the display flashes (for example t1) the number is
not currently allocated as a Pager Number pressing
YES will allocate it and the display will stop flashing.

If the display shows (for example t1) without flashing
the number is already allocated as a Pager Number
pressing NO will deselect it and the display will flash

Repeat this step for all Telephone Numbers you wish to
allocate as Pager Numbers.

6)

Press 0 the display will return to:-

7)

To program the Set Pager 16 digit message press 5
followed by YES (pressing NO will display the currently
stored Pager message) or go to step 10 to skip this option.
The display will flash showing:-

PR4100Rev1.7 SD.QXD 07/03/01 16:22 Page 34

«
...
32
33
34
35
36
...
»

Содержание GARDTEC SPEECH DIALLER







































Отзывы:

Нет отзывов