GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 38

GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Скачать руководство пользователя страница 24

35 volt monitor for lines not sharing with other equipment.

When you are satisfied with the Linefault Monitor shown
press YES and the dialler will return to step 1.

3)

Pressing 0 once will return to the 'P' display or twice will return
to the 'on' or 'oF' state.

7.10

PROGRAMMING MULTI-TRIGGER INHIBIT

No access is available to this option via the user code, it may only be accessed via
the engineer code.

Enter the engineers Menu (refer to section 7.0)

1)

With the display showing:-

2)

Enter 5. If NO is pressed the current Multi-Trigger Inhibit
state will be displayed and the dialler will return to step 1.

or

If YES is pressed the current Multi-Trigger Inhibit state will
be displayed.

Press NO to change the Multi-Trigger Inhibit to one of the
following:-

Multi-Trigger Inhibit is ON

Multi-Trigger Inhibit is OFF

When you are satisfied with the Multi-Trigger mode shown
press YES and the dialler will return to step 1.

3)

Pressing 0 once will return to the 'P' display or twice will
return to the 'on' or 'oF' state.

Note:

Multi-Trigger Inhibit should be programmed to ON if the trigger mode is
programmed for 'CP'

PR4100Rev1.7 SD.QXD 07/03/01 16:22 Page 24

«
...
22
23
24
25
26
...
»

Содержание GARDTEC SPEECH DIALLER







































Отзывы:

Нет отзывов