background image

3

www.coreservice.co.uk

AFTER SALES SUPPORT

IRE

GB

0845 872 2740

019022605

GPCS46Z, 06/14, 52579

General Information

2

Read and follow the operating instructions and 
safety information before using this product for 
the first time.

Read all safety regulations and instructions.
Any errors made in following the safety regulations and 
instructions may result in serious injury, fire or electric shock.
Keep all safety regulations and instructions in a safe place for 
future use. When using equipment, a few safety precautions 
must be observed to avoid injuries and damage. Please read the 
complete operating manual with due care. Keep this manual 
in a safe place, so that the information is available at all times. 
If you give the equipment to any other person, give them 
these operating instructions as well. We accept no liability for 
damage or accidents which arise due to non-observance of these 
instructions and the safety information.

Warning! For safety reasons, the Chainsaw is not to be used 
by children, young people under 16 years of age, or any other 
persons who are not acquainted with these operating instructions.

Items supplied

Open the packaging and take out the equipment with care.
Remove the packaging material and any packaging and/or 
transportation braces (if applicable).
Check to see that all items are included.
Inspect the equipment and accessories for transport damage.
Keep the packaging until the end of the warranty period.

• 
• 

    

• 
• 
• 

Содержание 06/14






































Отзывы: