background image

7

www.coreservice.co.uk

AFTER SALES SUPPORT

IRE

GB

0845 872 2740

019022605

GPCS46Z, 06/14, 52579

Safety Instructions

3

Warning: When using petrol tools, basic safety precautions, 
including the following, should always be followed to reduce the 
risk of serious personal injury and/or damage to the unit.

Read all these instructions before operating this product and keep 
them stored in a safe place for future reference.
1.  DO NOT operate a chainsaw with one hand! Serious injury to 

the operator, helpers, bystanders, or any combination of these 
persons may result from one-handed operation. A chainsaw is 
intended for two-handed use only.

2.  Do NOT use the saw if you are tired, ill or under the influence 

of alcohol and/or drugs.

3.  Use safety footwear, snug-fitting clothing, protective gloves, 

as well as eye, hearing and head protection devices.

4.  Use caution when handling fuel. Move the chainsaw at least 

10 feet (3m) away from the fueling point before starting the 
engine.

5.  DO NOT allow other persons to be near when starting, cutting 

with the chainsaw. Keep bystanders and animals out of the 
work area.

6.  DO NOT start cutting until you have a clear work area, secure 

footing, and a planned retreat path from falling trees or 
branches.

7.  Keep all parts of your body away from the saws’ chain when 

the engine is running.

8.  Before you start the engine, make sure that the chain is not in 

contact with anything.

9.  Carry the chainsaw with the engine stopped, the chain bar 

and saw chain facing rearwards, and with the exhaust away 
from your body.

10.  NEVER use a chainsaw which is damaged, incorrectly set or 

incomplete or loosely assembled. Make sure that the chain 
rotation stops when the chain brake is applied.

11.  Shut off the engine before setting the chainsaw down.
12.  Use extreme caution when cutting a small size bush and 

saplings because slender material may catch in the saw chain 
and be whipped towards you or pull you off balance.

13.  When cutting a limb that is under tension, be alert for spring 

back so that you will not be struck when the tension in the 

Содержание 06/14






































Отзывы: