G&D DP-HR-U Скачать руководство пользователя страница 143

Страница: 143 / 196

User module »DP-HR-U-CON-Fiber-MC4«

Target and user modules (DP-HR-U) ·

138

Status displays

Front panel

Section

LED

Status

Meaning

Power

Red.

The optional power pack is connected and supplies 12 Volt.

Off

The optional power pack is not (properly) connected.

Main

The power pack is turned on and supplies the required

voltage.

Off

The power pack is turned off or the connection to the mains

could not be established.

Status

Trans.

The communication to the counterpart station is estab-

lished successfully.

Off

The communication to the counterpart station could not be

established.

System

Flashing

System is ready for operation or firmware update is

executed.

Off

Internal error

Console Video

Strong video signal at video input.

Off

No signal at video input, or the signal quality is too weak to

be processed by the system.

K/M

A local keyboard was detected.

Off

No power at PS/2 interface or USB bus.

Flashing

The CPU input (PS/2 or USB) is active and ready.

A local keyboard was not detected.

MC2

Video 2

Strong video signal at second video input.

Off

No signal at second video input, or the signal quality is too

weak to be processed by the system.

Trans. 2

The communication to the counterpart station is estab-

lished successfully.

Off

The communication to the counterpart station could not be

established.

Video 2

Trans. 2

Trans. 1
System

Main

Red.

Video 1

K/M

Status

Power

Service

Console

USB Devices

Содержание DP-HR-U





































































































































































































Результаты поиска

Содержание DP-HR-U

Отзывы:

Похожие инструкции для DP-HR-U

Бренды по названию

Популярные бренды

G&D DP-HR-U, Установка и эксплуатация

Результаты поиска

Содержание DP-HR-U

Отзывы:

Похожие инструкции для DP-HR-U

Бренды по названию

Популярные бренды