GAL GALaxy eHydro Скачать руководство пользователя страница 141

Страница: 141 / 248

GALaxy eHydro Elevator Controller Section 6

– Main CPU Faults & Detailed Faults

6-77

Table 6-0: Main CPU Faults

Faults

Description

Possible Cause/Suggested Fix

RUN I/O
Failed On

The RUN input or
output has failed on.

• The RUN relay has failed on or RUN relay contact has

failed in the closed position. Replace the RUN relay.

• Faulty RUNi input. Replace the RUNi input chip.

• Faulty RUN output. Replace the RUN output chip.

• The solenoid

common is shorted to GND. Refer to the

schematic and check the circuit with a meter.

Run Inhibit Rset Cnt

Run inhibit from reset
count

• Once the car is in Reset mode, the controller attempted 5

times to come off reset but it keeps being sent back to the
reset mode because of a fault condition.

S10 Fuse Blown Fault

The S10 input is off.
No Power on S10

• Short from S10 to GND.

Safety String Fault

Safety string fault
occurs from the
following conditions:

•

The safety string is
open from one of the
following inputs being
off: GOV, HSS, EXT,
CSS, CTS, FFS, CST,
MRSW.

• The safety string is open (One or more of the safety inputs

are off). Refer to the job prints and check all circuits ahead
of the MRSW input.

SD I/O Failed Off

The SD input or
output has failed off.

• Faulty SDi input. Swap input board to see if SDi input chip

is bad and replace input board if necessary.

• The SD solenoid is shorted to GND at the SD terminal.

Refer to the schematic and check the circuit with a meter.

• Faulty

SD output. Swap the output with another device to

verify if the output is bad and replace if necessary.

SD I/O Failed On

The SD input or
output has failed on.

• Faulty SDi input. Swap input board to see if SDi input chip

is bad and replace input board if necessary.

• The SD test jumper was left on the output after an I/O

test. Remove test jumper.

• Voltage back feed through the SD coil. Verify that the SD

solenoid is connected to the solenoid common. Refer to the
schematic and check the circuit with a meter.

• Faulty SD output. Swap the output with another device to

verify if the output is bad and replace if necessary.

Содержание GALaxy eHydro

























































































































































































































































Результаты поиска

Содержание GALaxy eHydro

Отзывы:

Похожие инструкции для GALaxy eHydro

Бренды по названию

Популярные бренды

GAL GALaxy eHydro, Руководство пользователя

Результаты поиска

Содержание GALaxy eHydro

Отзывы:

Похожие инструкции для GALaxy eHydro

Бренды по названию

Популярные бренды