Gaggenau CV 282, Инструкция по эксплуатации

Страница: 31 / 64

31
Automatic functions
en
▯
Cooking in a pressure cooker: Follow the
manufacturer's recommendations. Continue
cooking for the recommended time once the
audible signal has sounded. Set the temperature to
115
°C.
▯
Frying with a large amount of oil in the saucepan:
Heat the oil with the lid on. Once the audible signal
has sounded, remove the lid and add the food. Set
the temperature to 175
°C.
Notes
– Before you cook anything, make sure that the
silicone patch is completely dry.
– Always cook with the lid on. Exception: "Frying with
a large amount of oil in the saucepan", temperature
170
°C.
– If an audible signal does not sound, make sure that
the lid is on the saucepan.
– Never leave oil unattended when it is being heated.
Use oil or fat that is suitable for frying.Do not mix
different cooking fats together, e.g. oil and lard.
Mixtures of different fats may froth up when hot.
– If you are not satisfied with the cooking result, e.g.
when cooking potatoes, next time use more water
but keep the recommended temperature setting.
Setting the boiling point
The point at which water starts to boil depends on the
height of your home above sea level. You can change
the boiling point if water is boiling too strongly or not
strongly enough. To do this, proceed as follows:
▯
Select the basic setting
™†
; see the section
entitled
~
"Basic settings" on page 44
.
▯
The basic setting is set to 3 by default. If your home
is between 200 and 400 metres above sea level,
there is no need to change the boiling point. If not,
choose the correct setting from the following table
according to your altitude:
Note: The 100 °C temperature setting provides
efficient cooking even if the water does not bubble very
strongly during the heating process. If you are not
satisfied with the boiling result, however, you can
change the boiling point setting.
Connecting the wireless temperature sensor to the
control panel
You will need to connect the wireless temperature
sensor to the control panel before using the cooking
sensor functions for the first time.
To connect the wireless temperature sensor to the
control panel, follow the instructions below:
1 Call up the basic setting
™†
; see the section
entitled
~
"Basic settings" on page 44
.
The
¨
symbol lights up white.
2 Press the
¨
symbol. A signal sounds and the
¨
symbol lights up orange. The cooking zone
indicators light up white and the cooking sensor
indicators on the cooking zones flash.
Briefly press the
¨
symbol on the wireless
temperature sensor within 30 seconds.
3 Detection successful: The wireless temperature
sensor is detected in a few seconds. Three short
beeps sound and the
¨
symbol changes from
orange to white. The cooking sensor indicators on
the cooking zones go out.
Detection failed: Five beeps will sound. The
¨
symbol immediately changes from orange to white
and the cooking sensor indicators on the cooking
zones go out.
▯
The cooking sensor function is made available once
the temperature sensor has been connected to the
control panel correctly.
▯
If there is a fault with the temperature sensor, the
connection may not be established correctly for the
following reasons:
– Bluetooth communication error.
– You did not press the
¨
symbol on the
temperature sensor within 30 seconds of
selecting a hotplate.
– The battery in the temperature sensor has run
out.
Reset the wireless temperature sensor and follow
the connection procedure once again.
▯
If the temperature sensor and the control panel are
not connected correctly due to a transmission error,
follow the connection procedure once again.
If no connection can be established, inform the
after-sales service.
Resetting the wireless temperature sensor
1 Touch and hold the
¨
symbol for approximately 8-
10 seconds.
While you are doing this, the temperature sensor's
LED indicator will light up three times. When the
LED lights up for the third time, it will start to reset
the temperature sensor. At this point, you will need
to lift your finger off the symbol.
Once the LED goes out, this means that the
wireless temperature sensor has been reset.
2 Repeat the connection procedure from point 2.
Height
Setting value
™†
0–100 m
‚
100–200 m
ƒ
200–400 m
„
*
400–600 m
…
600–800 m
†
800–1000 m
‡
1000–1200 m
ˆ
1200–1400 m
‰
Over 1400 m
Š
* Basic setting