background image

7

GENERAL SAFETY INSTRUCTIONS (cont.) 

d.   Remove any adjusting key or wrench before turning the power tool on.

 A wrench or 

a key left attached to a rotating part of the power tool may result in personal injury.

e.   Do not overreach. Keep proper footing and balance at all times.

 This enables better 

control of the power tool in unexpected situations.

f.  Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing 

and gloves away from moving parts.

 Loose clothes, jewellery or long hair can be 

caught in moving parts.

g.  If devices are provided for the connection of dust extraction and collection 

facilities, ensure these are connected and properly used.

 Use of dust collection can 

reduce dust-related hazards.

h.   Do not let familiarity gained from frequent use of tools allow you to become 

complacent and ignore tool safety principles. 

A careless action can cause severe injury 

within a fraction of a second.

4.  Power tool use and care
a.  Do not force the power tool. Use the correct power tool for your application. 

The 

correct power tool will do the job better and safer at the rate for which it was designed.

b.  Do not use the power tool if the switch does not turn it on and off.

 Any power tool 

that cannot be controlled with the switch is dangerous and must be repaired.

c.  Disconnect the plug from the power source and/or the battery pack from the 

power tool before making any adjustments, changing accessories, or storing 

power tools.

 Such preventive safety measures reduce the risk of starting the power tool 

accidentally.

d.  Store idle power tools out of the reach of children and do not allow persons 

unfamiliar with the power tool or these instructions to operate the power tool.

 

Power tools are dangerous in the hands of untrained users.

e.  Maintain power tools. Check for misalignment or binding of moving parts, 

breakage of parts and any other condition that may affect the power tool’s 

operation. If damaged, have the power tool repaired before use.

 Many accidents  

are caused by poorly maintained power tools.

f.  Keep cutting tools sharp and clean.

 Properly maintained cutting tools with sharp 

cutting edges are less likely to bind and are easier to control.

g.  Use the power tool, accessories and tool bits etc. in accordance with these 

instructions, taking into account the working conditions and the work to be 

performed.

 Use of the power tool for operations different from those intended could 

result in a hazardous situation.

h.   Keep handles and grasping surfaces dry, clean and free from oil and grease.

 

Slippery handles and grasping surfaces do not allow for safe handling and control of the 

tool in unexpected situations.

5. Service
a.  Have your power tool serviced by a qualified repair person using only identical 

replacement parts.

 This will ensure that the safety of the power tool is maintained.

b.  If the supply cord is damaged, 

it must be replaced by the manufacturer, its service 

agent or similarly qualified persons in order to avoid a hazard.

Содержание FBDDP-7500





























Отзывы: