manualshive.com logo in svg

Fujitsu MHR2010AT, Руководство по эксплуатации продукта

Поделиться
Скачать
Fujitsu MHR2010AT Скачать руководство пользователя страница 91

5.3  Host Commands

C141-E145-02EN

5-17

Table 5.3 Command code and parameters (3 of 3)

Command code (Bit)

Parameters used

Command name

7

6

5

4

3

2

1

0

FR SC SN CY DH

DEVICE CONFIGURATION
IDENTIFY

1

0

1

1

0

0

0

1

Y

N

N

N

D

DEVICE CONFIGURATION SET

1

0

1

1

0

0

0

1

Y

N

N

N

D

READ NATIVE MAX ADDRESS
EXT

1

1

1

1

1

0

0

0

N

N

N

N

D

SET MAX ADDRESS EXT

1

1

1

1

1

0

0

1

N

Y

Y

Y

Y

FLUSH CACHE EXT

1

1

1

0

0

1

1

1

N

N

N

N

D

WRITE DMA EXT

0

0

1

1

0

1

0

1

N

Y

Y

Y

D

READ DMA EXT

0

0

1

0

0

1

0

1

N

Y

Y

Y

D

WRITE MULTIPLE EXT

0

0

1

1

1

0

0

1

N

Y

Y

Y

D

READ MULTIPLE EXT

0

0

1

0

1

0

0

1

N

Y

Y

Y

D

WRITE SECTOR (S) EXT

0

0

1

1

0

1

0

0

N

Y

Y

Y

D

READ SECTOR (S) EXT

0

0

1

0

0

1

0

0

N

Y

Y

Y

D

Notes:

FR:

Features Register

CY:

Cylinder Registers

SC:

Sector Count Register

DH: Drive/Head Register

SN:

Sector Number Register

R:

Retry at error

1 =  Without retry

0 =  With retry

Y:

Necessary to set parameters

Y*:

Necessary to set parameters under the LBA mode.

N:

Not necessary to set parameters (The parameter is ignored if it is set.)

N*:

May set parameters

D:

The device parameter is valid, and the head parameter is ignored.

Содержание MHR2010AT



























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды