manualshive.com logo in svg

Fujitsu MHR2010AT, Руководство по эксплуатации продукта

Fujitsu MHR2010AT - Жесткий диск для ноутбука с качественным производством и высокой производительностью. Для получения бесплатного руководства по эксплуатации посетите наш веб-сайт и скачайте его сами. manualshive.com. Узнайте все возможности и функции этого изделия, чтобы получить наилучший опыт использования.

Поделиться
Скачать
background image

6.3  Defect Processing

C141-E145-02EN

6-11

Sector (physical)

Cylinder 0
Head 0

Defec-
tive
sector

(Not used)

Alternate cylinder 0
Head 0

This is assigned to an unassigned sector.

Already
assigned

Notes:

1.

The alternate cylinder is assigned to an inner cylinder in each zone.

2.

When an access request for sector 5 is issued, the sector assigned for
alternating processing of the alternate cylinder must be accessed instead of
physical sector 5.

If an access request for sectors after sector 5 is issued, seek is executed to
cylinder 0, head 0 in order to continue processing.

Figure 6.6  Alternate cylinder assignment processing

(3) Automatic alternating processing

This device performs automatic alternating processing in the event of any of the
following errors.

•

 

Automatic alternating processing is attempted for read error recovery by
heightening the ECC correction capability while a read error retry is in
progress.

Before attempting automatic alternating processing, writing and reading of
already corrected data is repeated for the sector in which an error occurred.
If a read error does not occur during this reading operation, automatic
alternating processing is not performed.

•

 

If error recovery is not successful even if a write fault error retry is executed,
automatic alternating processing is performed.

Содержание MHR2010AT



























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHR2010AT

X-METAL 4065 Owner'S Manual preview
4065
Бренд: X-METAL Страницы: 36
USP Duramax Yardmate Owner'S Manual/ Instructions For Assembly preview
Duramax Yardmate
Бренд: USP Страницы: 25
i3 International SAN iS316 User Manual preview
SAN iS316
Бренд: i3 International Страницы: 89
Hama Tenus FlashPen Operating Instruction preview
Tenus FlashPen
Бренд: Hama Страницы: 4
Denios PolySafe Depot Type C User Manual preview
PolySafe Depot Type C
Бренд: Denios Страницы: 8
LaCie 301894 User Manual preview
301894
Бренд: LaCie Страницы: 22
Y-E Data YD-380 Maintenance Manual preview
YD-380
Бренд: Y-E Data Страницы: 48
Glyph GT103800-1000 Manual preview
GT103800-1000
Бренд: Glyph Страницы: 7
Acard ARS-2212 User Manual preview
ARS-2212
Бренд: Acard Страницы: 43
Tuff Nano CalDigit Windows Quick Start Manual preview
CalDigit
Бренд: Tuff Nano Страницы: 17
QNAP TS-130 User Manual preview
TS-130
Бренд: QNAP Страницы: 39
IBM SAN768B Installation, Service And User Manual preview
SAN768B
Бренд: IBM Страницы: 208
GARDEN MASTER GM1511 Assembly Instructions preview
GM1511
Бренд: GARDEN MASTER Страницы: 2
PQI Traveling Disk i161 Product Manual preview
Traveling Disk i161
Бренд: PQI Страницы: 7
Cavalry CAXE Series User Manual preview
CAXE Series
Бренд: Cavalry Страницы: 16
Cavalry CAUI Series User Manual preview
CAUI Series
Бренд: Cavalry Страницы: 16
Cavalry CADT-SA2 Series User Manual preview
CADT-SA2 Series
Бренд: Cavalry Страницы: 25
Costway 02836975 Operating Instructions preview
02836975
Бренд: Costway Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды