manualshive.com logo in svg

Fujitsu MHR2010AT, Руководство по эксплуатации продукта

Fujitsu MHR2010AT - Жесткий диск для ноутбука с качественным производством и высокой производительностью. Для получения бесплатного руководства по эксплуатации посетите наш веб-сайт и скачайте его сами. manualshive.com. Узнайте все возможности и функции этого изделия, чтобы получить наилучший опыт использования.

Поделиться
Скачать
background image

5.5  Ultra DMA Feature Set

C141-E145-02EN

5-115

5.5 Ultra DMA Feature Set

5.5.1 Overview

Ultra DMA is a data transfer protocol used with the READ DMA and WRITE
DMA commands.  When this protocol is enabled it shall be used instead of the
Multiword DMA protocol when these commands are issued by the host.  This
protocol applies to the Ultra DMA data burst only.  When this protocol is used
there are no changes to other elements of the ATA protocol (e.g.:  Command
Block Register access).

Several signal lines are redefined to provide new functions during an Ultra DMA
burst.  These lines assume these definitions when 1) an Ultra DMA Mode is
selected, and 2) a host issues a READ DMA or a WRITE DMA, command
requiring data transfer, and 3) the host asserts DMACK-.  These signal lines
revert back to the definitions used for non-Ultra DMA transfers upon the negation
of DMACK- by the host at the termination of an Ultra DMA burst.  All of the
control signals are unidirectional.  DMARQ and DMACK- retain their standard
definitions.

With the Ultra DMA protocol, the control signal (STROBE) that latches data
from DD (15:0) is generated by the same agent (either host or device) that drives
the data onto the bus.  Ownership of DD (15:0) and this data strobe signal are
given either to the device during an Ultra DMA data in burst or to the host for an
Ultra DMA data out burst.

During an Ultra DMA burst a sender shall always drive data onto the bus, and
after a sufficient time to allow for propagation delay, cable settling, and setup
time, the sender shall generate a STROBE edge to latch the data.  Both edges of
STROBE are used for data transfers so that the frequency of STROBE is limited
to the same frequency as the data.

Words in the IDENTIFY DEVICE data indicate support of the Ultra DMA feature
and the Ultra DMA Modes the device is capable of supporting.  The Set transfer
mode subcommand in the SET FEATURES command shall be used by a host to
select the Ultra DMA Mode at which the system operates.  The Ultra DMA Mode
selected by a host shall be less than or equal to the fastest mode of which the
device is capable.  Only the Ultra DMA Mode shall be selected at any given time.
All timing requirements for a selected Ultra DMA Mode shall be satisfied.
Devices supporting Ultra DMA Mode 2 shall also support Ultra DMA Modes 0
and 1.  Devices supporting Ultra DMA Mode 1 shall also support Ultra DMA
Mode 0.

An Ultra DMA capable device shall retain its previously selected Ultra DMA
Mode after executing a Software reset sequence.  An Ultra DMA capable device
shall clear any previously selected Ultra DMA Mode and revert to its default non-
Ultra DMA Modes after executing a Power on or hardware reset.

Both the host and device perform a CRC function during an Ultra DMA burst.  At
the end of an Ultra DMA burst the host sends the its CRC data to the device.  The

Содержание MHR2010AT



























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHR2010AT

NEC Express5800/R120f-2E Configuration Manual preview
Express5800/R120f-2E
Бренд: NEC Страницы: 36
LaCie d2 Ethernet Disk mini Quick Install Manual preview
d2 Ethernet Disk mini
Бренд: LaCie Страницы: 23
kincrome K7795 Operation Manual preview
K7795
Бренд: kincrome Страницы: 3
ManoMano 03POH1010-V2 Instructions Manual preview
03POH1010-V2
Бренд: ManoMano Страницы: 8
LaCie 2big DOCK User Manual preview
2big DOCK
Бренд: LaCie Страницы: 48
Seagate ST52160N Installation Manual preview
ST52160N
Бренд: Seagate Страницы: 40
Lifetime 60209 Assembly Instructions Manual preview
60209
Бренд: Lifetime Страницы: 52
Y-E Data YD-380 Maintenance Manual preview
YD-380
Бренд: Y-E Data Страницы: 48
Hama Save2Data SecureKey Operating Instructions Manual preview
Save2Data SecureKey
Бренд: Hama Страницы: 38
EMC CLARiiON CX4-120 Setup Manual preview
CLARiiON CX4-120
Бренд: EMC Страницы: 62
IBM Storwize V5000E Quick Installation Manual preview
Storwize V5000E
Бренд: IBM Страницы: 120
Wayfair G37016 Manual Instruction preview
G37016
Бренд: Wayfair Страницы: 22
Lakeshore LC104 Manual preview
LC104
Бренд: Lakeshore Страницы: 7
Samsung HN-M101MBB Specifications preview
HN-M101MBB
Бренд: Samsung Страницы: 1
Samsung HS030GB User Manual preview
HS030GB
Бренд: Samsung Страницы: 2
Samsung HD161HJ - SpinPoint S166 160 GB Hard Drive User Manual preview
HD161HJ - SpinPoint S166 160 GB Hard Drive
Бренд: Samsung Страницы: 2
Samsung HD321KJ - SpinPoint T166 320 GB Hard Drive Product Manual preview
HD321KJ - SpinPoint T166 320 GB Hard Drive
Бренд: Samsung Страницы: 22
Toshiba STOR.E TV Brochure & Specs preview
STOR.E TV
Бренд: Toshiba Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды