Fujitsu MHR2010AT страница 155 Скачать руководство пользователя | Manualshive

Страница: 155 / 250

background image

5.3 Host Commands

C141-E145-02EN

5-81

(30) SECURITY DISABLE PASSWORD (F6h)

This command invalidates the user password already set and releases the lock
function.

The host transfers the 512-byte data shown in Table 5.13 to the device. The
device compares the user password or master password in the transferred data
with the user password or master password already set, and releases the lock
function if the passwords are the same.

Although this command invalidates the user password, the master password is
retained. To recover the master password, issue the SECURITY SET
PASSWORD command and reset the user password.

If the user password or master password transferred from the host does not match,
the Aborted Command error is returned.

Issuing this command while in LOCKED MODE or FROZEN MODE returns the
Aborted Command error.

(The section about the SECURITY FREEZE LOCK command describes
LOCKED MODE and FROZEN MODE.)

«
...
153
154
155
156
157
...
»

Содержание MHR2010AT



























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHR2010AT

NSLU2 - Network Storage Link NAS Server

Бренд: Linksys Страницы: 64

Бренд: Magnusson Страницы: 18

Бренд: Western Digital Страницы: 2

Бренд: Synology Страницы: 28

HPRO72TLOCKERBLK

Бренд: Husky Страницы: 8

Бренд: SonicWALL Страницы: 56

BAULE WOODY GREY 80

Бренд: garofalo Страницы: 16

Бренд: NITEO TOOLS Страницы: 8

Бренд: DURHAND Страницы: 16

Бренд: Clarke Страницы: 12

Бренд: Heartland Страницы: 71

Бренд: ramia Страницы: 3

Бренд: Arrow Страницы: 32

SafeTANK GT4670-TB3

Бренд: Raidon Страницы: 31

Personal Secure Flash Drive Personal

Бренд: IronKey Страницы: 32

01OVLP0604-V1-NW

Бренд: Walton Страницы: 4

Бренд: NAS Страницы: 23

TotalStorage FAStT700

Бренд: IBM Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды