Fujitsu DL9300 Скачать руководство пользователя

Страница: 84 / 250

User's Manual

Paper

Handling

PAPER HANDLING

3-27

Labels

• Be careful to check operating conditions when using labels.

Labels are sensitive to temperature and humidity.

• Only use labels mounted on continuous forms backing sheets.

Do not print labels mounted on single sheet backing. Labels
mounted on single sheet backing tend to slip and printing
becomes crooked.

• Do not feed labels backwards using the LOAD button from the

control panel. Jamming may occur.

• Do not use the printer tear-off feature when printing labels. If

the labels are retracted, the backing may peel off and the labels
may jam in the printer.

• Test-print labels before running a job. If jams occur, go into

setup mode and set the paper thickness control to manual mode
and set the paper thickness indicator to a wider position
manually. If jamming problems continue, try a different type of
label.

Содержание DL9300



























































































































































































































































Результаты поиска

Содержание DL9300

Отзывы:

Похожие инструкции для DL9300

Бренды по названию

Популярные бренды

Fujitsu DL9300, Руководство пользователя

Результаты поиска

Содержание DL9300

Отзывы:

Похожие инструкции для DL9300

Бренды по названию

Популярные бренды