Fujitsu DL9300 Скачать руководство пользователя

Страница: 139 / 250

USING SETUP MODE

User's Manual

5-48

Select the V-ALMNT function.

Repeatedly press the “

←

” or “

→

” button to position the red

cursor under V-ALMNT, then press the “

↑

” button or the “

↓

”

button to select the V-ALMNT function. The printer prints the
help menu then starts printing rows of parallel bars using
letter quality speed.

Adjust the vertical print alignment at letter quality speed.

Examine the parallel bars. If the bars are aligned (not jagged),
go to step 4. If the bars are offset to the left, repeatedly press
the “

→

” button until the bars are aligned. If the bars are offset

to the right, repeatedly press the “

←

” button until the bars are

aligned. (In the following figure, the first line is assumed to be
printed from left to right.)

Bars offset to the left Bars offset to the right

Adjust the vertical print alignment at correspondence speed.

Press the “

↓

” button to switch from letter speed to correspond-

ence speed.

Examine the parallel bars and adjust the vertical print align-
ment as described step 3.

Adjust the vertical print alignment at draft speed.

Press the “

↓

” button to switch from correspondence speed to

draft speed.

Examine the parallel bars and adjust the vertical print align-
ment as described step 3.

Содержание DL9300



























































































































































































































































Результаты поиска

Содержание DL9300

Отзывы:

Похожие инструкции для DL9300

Бренды по названию

Популярные бренды

Fujitsu DL9300, Руководство пользователя

Результаты поиска

Содержание DL9300

Отзывы:

Похожие инструкции для DL9300

Бренды по названию

Популярные бренды