Fujitsu DL9300 Скачать руководство пользователя | Manualshive

Страница: 2 / 250

background image

Federal Communications Commission

Radio Frequency Interference Statement

for United States Users

NOTE:

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15B of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measure:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC warning:

Changes or modifications not expressly

approved by the party responsible for compliance could void
the user’s authority to operate the equipment.

NOTES

1. Testing of this equipment was performed on model number

M33021A or M33011A.

2. The use of a nonshielded interface cable with the referenced

device is prohibited. The length of the parallel interface cable
must be 3 meters (10 feet) or less. The length of the serial interface
cable must be 15 meters (50 feet) or less.

3. The length of the power cord must be 3 meters (10 feet) or less.

«
1
2
3
4
...
»

Содержание DL9300



























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DL9300

Бренд: Canon Страницы: 11

imageRUNNER ADVANCE 8085

Бренд: Canon Страницы: 176

Бренд: Canon Страницы: 85

imageRUNNER 5070

Бренд: Canon Страницы: 4

imageRUNNER 5570

Бренд: Canon Страницы: 4

IMAGERUNNER 7095 PRINTER

Бренд: Canon Страницы: 8

IMAGERUNNER 7105

Бренд: Canon Страницы: 21

Бренд: Canon Страницы: 58

IMAGERUNNER ADVANCE C5051

Бренд: Canon Страницы: 12

imageRUNNER ADVANCE C2020

Бренд: Canon Страницы: 68

imageRUNNER ADVANCE 6055

Бренд: Canon Страницы: 134

Color imageRUNNER LBP5970

Бренд: Canon Страницы: 67

FAXPHONE L170 - B/W Laser - Copier

Бренд: Canon Страницы: 12

Бренд: Canon Страницы: 2

imageRunner 1133

Бренд: Canon Страницы: 60

Color imageCLASS MF8280Cw

Бренд: Canon Страницы: 36

Бренд: Canon Страницы: 104

imagePROGRAF iPF8300

Бренд: Canon Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды