Fujitsu DL9300 Скачать руководство пользователя

Страница: 235 / 250

GL-2

User's Manual

GLOSSARY OF TERMS

Carriage return (CR)

Centronics interface

Column

Command set

Condensed print

Continuous forms

Control panel

cpi

cps

Cut sheets

Cut sheet feeder

Defaults

The return of the print head carriage to the beginning of the

next line.

A type of parallel interface. See Parallel interface.

A vertical section on a printed page. This printer can print 136-

column pages at 10-pitch (10 characters per inch).

A set of print and format commands used to control the

printer. Each printer has its own resident command sets
embedded in the printer firmware. These command sets are
actuated by codes sent from the host computer.

Print that uses “condensed” characters. Condensed characters

are narrower than regular characters. Using condensed print
increases the number of characters per line.

Connected, fan-folded sheets of paper that are fed into the

printer using forms tractors. The fan-folded sheets are
separated by tearing them at their perforations.

A panel containing the printer indicators and buttons. The control

panel is used to control printer operations, such as loading paper,
selecting print features, and changing setup options.

Characters per horizontal inch. Also referred to as pitch. For

example, 12-pitch means 12 cpi.

Characters per second.

See Single sheets.

An option that allows automatic loading from a stack of cut

sheet paper.

Settings selected automatically by the printer when power is

turned on. Enter setup mode to change the defaults to ensure
compatibility with your system hardware and software.

Содержание DL9300



























































































































































































































































Результаты поиска

Содержание DL9300

Отзывы:

Похожие инструкции для DL9300

Бренды по названию

Популярные бренды

Fujitsu DL9300, Руководство пользователя

Результаты поиска

Содержание DL9300

Отзывы:

Похожие инструкции для DL9300

Бренды по названию

Популярные бренды