manualshive.com logo in svg

Fujitsu DL9300, Руководство пользователя

Fujitsu DL9300 - профессиональный принтер для офиса с высоким качеством печати. Пользователям доступен бесплатный скачиваемый руководство пользователя на manualshive.com. Необходимое руководство в формате PDF можно скачать бесплатно. Узнайте, как максимально эффективно использовать свой принтер Fujitsu DL9300.

Поделиться
Скачать
background image

Setup Mode

USING SETUP MODE

User's Manual

5-43

Printing the Self-Test

The SELF-TST function prints test pages to check how the printer
operates independently of your computer.  The self-test does not
check the interface between the computer and the printer.

The self-test prints the printer’s firmware version, its resident
emulations, and all of the characters available in the currently selected
character set.  If the DPL24C PLUS emulation is selected for MENU1,
the self-test is printed using the settings currently assigned to MENU1.

Procedure

This procedure assumes that you are in setup mode.  To print the self-
test, make sure that continuous forms paper is loaded into the printer.
Then proceed as follows:

1.

Print the <<FUNCTION>> menu.

The <<FUNCTION>> menu should be the last printed line on the
page.  If the menu is not printed, press the ONLINE button to
print the menu.  If you are using the HEX-DUMP function, press
the “

←

” or “

→

” button instead of the ONLINE button to print

the menu.  The following <<FUNCTION>> menu is printed:

<<FUNCTION>>

SAVE&END

MENU1

MENU2

HARDWRE

ADJUST

CONFIG

DEFAULT

LIST

SELF-TST

HEX-DUMP

V-ALMNT

GAP-ADJ

Содержание DL9300



























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DL9300

Eaton Power Defense PD3 Mounting And Operating Instructions preview
Power Defense PD3
Бренд: Eaton Страницы: 4
F+D Feinwerk- und Drucktechnik TOP-ino Operating Instructions Manual preview
TOP-ino
Бренд: F+D Feinwerk- und Drucktechnik Страницы: 22
GCC Technologies Elite 12N Network Manual preview
Elite 12N
Бренд: GCC Technologies Страницы: 63
gCreate gMax 2 PRO Unboxing And Setup Instructions preview
gMax 2 PRO
Бренд: gCreate Страницы: 9
GCC Technologies Elite XL-1208 Supplementary Manual preview
Elite XL-1208
Бренд: GCC Technologies Страницы: 9
GCC Technologies Elite XL-1208 Install Manual preview
Elite XL-1208
Бренд: GCC Technologies Страницы: 12
gCreate gMax 2 PRO User Manual preview
gMax 2 PRO
Бренд: gCreate Страницы: 21
GCC Technologies Elite XL User Manual preview
Elite XL
Бренд: GCC Technologies Страницы: 199
Xerox DocuColor 6060 Recommended Materials List preview
DocuColor 6060
Бренд: Xerox Страницы: 4
Lexmark 7016-630 Service Manual preview
7016-630
Бренд: Lexmark Страницы: 455
Oce VarioPrint 6000 MICR series User Manual Operating Information preview
VarioPrint 6000 MICR series
Бренд: Oce Страницы: 264
Oce im2330 User Manual preview
im2330
Бренд: Oce Страницы: 194
Xerox Phaser 5335 Installation Manual preview
Phaser 5335
Бренд: Xerox Страницы: 2
Xerox Phaser 6250DP Setup Manual preview
Phaser 6250DP
Бренд: Xerox Страницы: 2
Xerox Phaser 6280N Evaluator Manual preview
Phaser 6280N
Бренд: Xerox Страницы: 16
Canon imageRUNNER ADVANCE DX C478iZ Faq Manual preview
imageRUNNER ADVANCE DX C478iZ
Бренд: Canon Страницы: 208
Canon imageRUNNER ADVANCE DX C477iFZ Faq Manual preview
imageRUNNER ADVANCE DX C477iFZ
Бренд: Canon Страницы: 92
Kodak 8437477 - EasyShare ESP 9 All-In-One Printer User Manual preview
8437477 - EasyShare ESP 9 All-In-One Printer
Бренд: Kodak Страницы: 143

Бренды по названию

Популярные бренды

Загрузить еще бренды