Fujitsu AOYG09KMCBN Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 61

background image

Troubleshooting 7

INDOOR UNIT Error Method:

Detective Actuators:

Detective details:

Forecast of cause:

Check Point 1 : Check rotation of Fan

Check Point 2 : Check ambient temp. around motor

OK

OK

OK

Indoor unit fan motor error

Indoor unit Controller PCB

Indoor unit Fan motor

1. Fan rotation failure

2. Fan motor winding open

3. Motor protection by surrounding temperature rise

4. Control PCB failure

5. Indoor unit fan motor failure

Rotate the fan by hand when operation is off.

(Check if fan is caught, dropped off or locked motor)

>>If Fan or Bearing is abnormal, replace it.

Check excessively high temperature around the motor.

(If there is any surrounding equipment that causes heat)

>>Upon the temperature coming down, restart operation.

When the condition that actual frequency of Indoor Fan is

below 1/3 of target frequency is continued more than 56 seconds.

02-11

Check Point 4 : Replace Controller PCB

If Check Point 1- 3 do not improve the symptom,

replace controller PCB.

Check Point 3 : Check Indoor unit fan motor

Check Indoor unit fan motor. (PARTS INFORMATION 4)

>>If Indoor unit fan motor is abnormal, replace Indoor unit fan motor.

«
...
37
38
39
40
41
...
»

Содержание AOYG09KMCBN






























































Отзывы:

Нет отзывов

Похожие инструкции для AOYG09KMCBN

Бренд: Ideal Air Страницы: 28

Бренд: NANO Страницы: 28

Split Type Room Air Conditioner

Бренд: Midea Страницы: 14

Бренд: Carrier Страницы: 104

Бренд: Daikin Страницы: 16

CoolAir CA-1000-AC

Бренд: Waeco Страницы: 220

Бренд: Airwell Страницы: 20

Бренд: Saivod Страницы: 88

Бренд: Olmo Страницы: 19

Бренд: Carrier Страницы: 10

Бренд: oneConcept Страницы: 26

PURE LIGHT UV HTWS026PLUV

Бренд: HTW Страницы: 88

Бренд: Technibel Climatisation Страницы: 21

Бренд: ACPro Страницы: 20

Бренд: Delta Страницы: 32

Бренд: Daikin Страницы: 28

Бренд: Daikin Страницы: 12

VRV FXMQ50P7VEB9

Бренд: Daikin Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды