Fujitsu AOY54LJBYL Скачать руководство пользователя страница 46

Страница: 46 / 60

Installation and operating manual “1350-EN”

Heat pump, Split, single service

Configuring the installation

Optional DHW kit

DHW tank control (with electrical back-up) requires

the use of the DWH kit.
Warning: The tank must be fitted with an electric

back-up, particularly for anti-legionella cycles.
Please refer to section (Operating principle, page 13)

Optional 2nd circuit kit

The control of 2 heating circuits requires the

installation of the 2nd circuit.
If the installation consists of radiators (or

fan-convectors) and a heated floor, zone 2 will

correspond to the radiator (or fan-convectors) zone

and

zone 1 to the heated floor zone

Optional boiler connection kit

The connection of an oil or gas boiler to the heat

pump requires the installation of the boiler

connection kit.

When a boiler is connected to the heat pump, the

heat pump’s electric back-ups must not be

connected. It is the boiler that provides the

heating back-up on the coldest days.

The boiler is controlled by the heat pump.
Please refer to the instructions supplied with the

boiler connection kit.

Swimming pool kit option

Please refer to the instructions supplied with the

swimming pool kit.

Configuration

(Parameter 5700)

Type of installation

Page

Pre-setting

1 heating circuit

Pre-setting

1 heating circuit and DHW tank

Pre-setting

2 heating circuits

Pre-setting

2 heating circuits and DHW tank

Pre-setting

Boiler connection and 1 heating circuit

Please refer to the

instructions supplied

with the boiler

connection kit.

Pre-setting

Boiler connection and 2 heating circuits

Pre-setting

Boiler connection, 1 heating circuit and DHW tank

Pre-setting

Boiler connection, 2 heating circuits and DHW tank

Pre-setting 9

Do not use for heat pump single service. Reserved only for heat pump 2 services

Pre-setting 10
Pre-setting 11
Pre-setting 12

Please consult us regarding any other installation configuration.

Содержание AOY54LJBYL





























































Результаты поиска

Содержание AOY54LJBYL

Отзывы:

Похожие инструкции для AOY54LJBYL

Бренды по названию

Популярные бренды

Fujitsu AOY54LJBYL, Инструкция по установке и эксплуатации

Результаты поиска

Содержание AOY54LJBYL

Отзывы:

Похожие инструкции для AOY54LJBYL

Бренды по названию

Популярные бренды