background image

2

Installation

2.1

Regulation installation and

maintenance conditions

The appliance must be installed and the maintained

by an approved professional in accordance with the

prevailing regulations and code of practice, in

particular:

The legislation on the handling of refrigerants.

2.2

Unpacking and reservations

2.2.1

Receipt

Carefully check, in the carrier’s presence, the

general appearance of the appliances and check

that the outside unit is not laid on its side or back.
In the case of any dispute, state any appropriate

reservations to the carrier in writing within 48 hours

and send a copy of this letter to the After-Sales

service.

2.2.2

Handling

The outside unit should not be laid on its side or back

during transport.
Laying the unit down during transport is likely to

damage the internal tubes and the compressor

suspensions.
Any damage caused by transportation of the unit

lying down is not covered by the warranty.
If necessary the outside unit may be tilted only during

manual handling (to go through a door or use a

staircase).
This operation must be conducted very carefully and

the appliance must be immediately restored to

upright position.

2.2.3

Accessories provided

Accessories provided with the outside unit

(figure 10).
Accessories provided with the hydraulic module

(figure 11)

2.3

Installation position

The choice of the position for installation is

particularly important insofar as any later movement

is a delicate operation requiring the intervention of a

qualified person.
Choose the site of the outside unit and the hydraulic

module after discussion with the customer.
Observe the maximum and minimum distances

between the hydraulic module and the outside unit

(Figure 13); the guarantee of the performances and

the system’s service life depend on this.

2.4

Installation of the outside unit

2.4.1

Installation precautions

F

The outside unit must only be installed

outside (outdoors). If a shelter is required, it

must have broad openings on the 4 walls and

observe the installation clearances (fig. 12).

Choose a site that is preferably sunny and sheltered

from strong cold predominant winds (mistral,

tramontana, etc…).

The unit must be easily accessible for future

installation and maintenance work (fig. 12).

Ensure that it is possible to make the connections to

the hydraulic module easily.

14

Installation and operating manual “1350-EN”

Heat pump, Split, single service

1

3

2

4

Figure 10 - Accessories provided

with the outside unit

8

5

6

7

Figure 11 - Accessories provided

with the hydraulic module

1

Elbow

For draining away the
condensates

2

Plug (x 2)

(Depending

on the model)

3

Flexible

i n s u l a t i o n

plate

For filling the empty
space at the input to the
interconnection cable

4

Hex / Allen

key

To open the valves

5

Bracket

To secure the
hydraulic model

6

Outdoor sensor

To monitor the

outside temp

7

1/2" - 5/8" and/or

1/4" - 3/8" adapter

To connect the
flared connection
and the hydraulic
model

8

Nut (1/2" and/or)

1/4"

Содержание AOY54LJBYL





























































Отзывы: