Fujitsu AOY54LJBYL Скачать руководство пользователя страница 13

Страница: 13 / 60

Domestic hot water (DHW) operating principl

Two domestic hot water (DHW) temperatures can be

parametered: comfort temperature (line 1610 to 60

°C) and reduced temperature (line 1612 to 40 °C).
Setting for reduced temperature can be useful to

prevent the DHW from switching on too often and for

too long during the day.
The production of domestic hot water (DHW) is

triggered when the temperature in the tank falls 7°C

(setting from line 5024) below the set temperature.
The heat pump produces the domestic hot water,

which is then supplemented, if required, by electrical

backup heating from the tank.
Depending on how the parameter (1620) is set,

comfort temperature can be reached 24h/day or only

at night or depending on the heat pump programme.
If the contract concluded with the energy provider

includes a subscription to day/night tariff, the

electrical backup is subordinate to the supplier’s

power tariff and the comfort temperature may only be

reached at night.

If no particular contract is concluded, the comfort

temperature can be reached at any time, including

during the day
The production of DHW takes priority over heating;

nevertheless the production of DHW is controlled by

cycles that control the times assigned to the heating

and the production of DHW in the event of

simultaneous demand.
A DHW “ boost” function is available on the front of

the user interface (see ref. 1, fig. 39, p 31).
This DHW boost enables the DHW to be heated to

the comfort temperature at any time during the day.

The boost function is cancelled automatically when

the demand for hot water has been met.
If the heating installation is equipped with a DHW

circulation pump, the pump’s operation during DHW

cycles can be parametered.
Anti-legionella cycles can be programmed.

Installation and operating manual “1350-EN”

Heat pump, Split, single service

PAC

1 kW

COP 4

4 kW

20 °C

Electrical

energy

consumed

Energy from the air

Heat produced

Figure 9 - Heat pump operating principle

PAC

- Heat pump

- Evaporator

- Compressor

- Condenser

- Expansion valve

Содержание AOY54LJBYL





























































Результаты поиска

Содержание AOY54LJBYL

Отзывы:

Похожие инструкции для AOY54LJBYL

Бренды по названию

Популярные бренды

Fujitsu AOY54LJBYL, Инструкция по установке и эксплуатации

Результаты поиска

Содержание AOY54LJBYL

Отзывы:

Похожие инструкции для AOY54LJBYL

Бренды по названию

Популярные бренды