Fujitsu AB*A12 Скачать руководство пользователя

Страница: 121 / 322

Trouble shooting 19

OUTDOOR UNIT Error Method:
High Pressure Error

Indicate or Display:

Outdoor Unit : LED1 Flash, LED2

7 Times Blink

Indoor Unit : Operation LED Lighted Continuously (Normal operation)

ERROR CODE : E : 00

Detective Actuators:

Outdoor Unit Controller PCB circuit

Discharge Pressure Sensor

Detective details:

When Discharge pressure of higher than 4.1 Mpa is detected 3 times

repeatedly within 60 minutes, upon Discharge (High Pressure) pre is

detected at higher than 4.1 Mpa.

Check Point 1 : Check if Liquid Pipe Valve is open

If not open, open it and check the operation.

Check Point 2 : Check Outdoor FAN, Heat Exchanger

Is there anything obstructing the air distribution circuit?

Is there any clogging of Outdoor Heat Exchanger?

Is the Fan rotating? (Check by hand and If it is locked, replace the motor)

Check Outdoor Fan Motor

(PARTS INFORMATION 12)

>>If the Fan Motor is defective, replace it.

Check Point 3 : Check EEV and Solenoid Valve

Is Solenoid Valve (SV1, SV4 of Main Unit) open?

(PARTS INFORMATION 8,9)

>>If EEV or Solenoid Valve is defective, replace it.

Check Point 4 : Recharge Refrigerant

Check the operation after recharging the refrigerant, because there is a

possibility of refrigerant overcharge.

>>When recharging the refrigerant, make sure to perform vacuuming and

charge with the specified amount.

MPa MPa

Forecast of Cause :

1. Liquid Pipe Valve is close 2. Outdoor FAN failure 3. Outdoor Heat Exchanger clogged

4. Solenoid Valve failure 5. Refrigerant overcharged

06-30

(If Gas valve close, Low pressure or Discharge temperature error.)

Check Point 1 : Check if Gas Valve is open

If it is not open, open it and check the operation.

(If valve close, Low pressure or Discharge

temperature error.)

< Heating mode >

< Cooling mode >

(No error display)

Содержание AB*A12



































































































































































































































































































































Результаты поиска

Содержание AB*A12

Отзывы:

Похожие инструкции для AB*A12

Бренды по названию

Популярные бренды

Fujitsu AB*A12, Руководство по обслуживанию

Результаты поиска

Содержание AB*A12

Отзывы:

Похожие инструкции для AB*A12

Бренды по названию

Популярные бренды