Fujitsu AB*A12 Скачать руководство пользователя страница 179

Страница: 179 / 322

SERVICE PARTS INFORMATION 1

Compressor

Does not start up

Diagnosis method of Compressor (If Outdoor Unit LED displays Error, refer to Trouble shooting 13 to 48)

Replace Compressor

Is any Indoor Unit in operation?

* If it is operated right after stopping

operation, 3 minutes start-up protection

by differential pressure is kicked on.

Stops soon after starting up

Abnormal noise

Check power supply voltage,open

fuse.

Is there open or loose connection

cable?

Check power supply voltage,open

fuse.

Is there open or loose connection

cable?

In case of constant speed compressor, check connection

and winding resistance.(Check if Protector is operated) Refer to

the next page.

In case of inverter compressor, check Filter PCB, Inverter

PCB, connection of Compressor, and winding resistance. (Refer

to the next page).

>> If there is no failure, the defect of Compressor can be

considered. (Compression part broken or valve defective.)

In case of constant speed

compressor, check connection and

winding resistance.(Check if Protector

is operated) Refer to the next page.

In case of inverter compressor, check

Filter PCB, Inverter PCB, connection of

Compressor, and winding resistance

(Refer to the next page).

>> If there is no failure, the defect of

Compressor is considered (Locked

compressor due to clogged dirt or

less oil)

Replace Compressor

Check if Refrigerant is leaking.

(Recharge Refrigerant)

Isn’t it Liquid Compression?

>> Check Low pressure value and if

it too high, check Indoor Unit.

(Indoor Unit EEV too much open, or

Indoor unit EEV that is not in

operation open.

Replace Compressor

Check power supply

voltage,open fuse. Is there

open or loose connection

cable?

Defective Compressor

can be considered.

(due to inside dirt clogging

or broken component)

Is Gas Pipe Valve open?

(Low Pressure is too low)

Check if Strainer is clogged.

(PARTS INFORMATION 5,6,7)

MPa MPa

06-88

6-5 SERVICE PARTS INFORMATION

Содержание AB*A12



































































































































































































































































































































Результаты поиска

Содержание AB*A12

Отзывы:

Бренды по названию

Популярные бренды

Fujitsu AB*A12, Руководство по обслуживанию

Результаты поиска

Содержание AB*A12

Отзывы:

Бренды по названию

Популярные бренды