Fujitsu AB*A12 Скачать руководство пользователя

Страница: 69 / 322

04-07

4-5-2 Oil balance operation

(1) Purpose of the operation

Divide the oil equally between the outdoor units.

The master unit is operating

This is the end of oil balance operation.

(2) Starting conditions

(3) About oil balance operation (Example)

When only one outdoor unit is connected : Oil balance operation does not operate.

a) Oil balance operation (Slave unit Master unit)

SV7(Slave1) and SV6(Master) : Open for 1 min.

Accumulated time of compressor operation 20 min.

After oil recovery and defrost operation, when discharge SH is15 or more.

Master

Operation

Slave 1

Operation or stop

Slave 2

Operation or stop

SV7(Slave2) and SV6(Master) : Open for 1 min.
Oil is recovered to the master unit by operation & .

b) Oil distribution operation (Master unit Slave unit)

60 seconds after the oil recovery finish, master unit sends accumulated oil to the slave unit.

Oil shares in only a operating slave unit.

(Master unit SV7 open, operating slave unit SV6 open)

Oil distribution operation for 60 seconds and is finished.

Содержание AB*A12



































































































































































































































































































































Результаты поиска

Содержание AB*A12

Отзывы:

Похожие инструкции для AB*A12

Бренды по названию

Популярные бренды

Fujitsu AB*A12, Руководство по обслуживанию

Результаты поиска

Содержание AB*A12

Отзывы:

Похожие инструкции для AB*A12

Бренды по названию

Популярные бренды