Fujitsu AB*A12 Скачать руководство пользователя

Страница: 111 / 322

Trouble shooting 13

OUTDOOR UNIT Error Method:
Compressor 1 Abnormal
(Inverter Compressor)

Indicate or Display:

Outdoor Unit : LED1 Flash, LED2

1 Time Blink

Indoor Unit : Operation LED Flash, Timer LED 3 Time Blinks,

ERROR CODE : E : 32

Detective Actuators:

Outdoor Unit Controller PCB circuit

Discharge Thermistor

Detective details:

06-20

Swing LED 3 Time Blinks

6-3-3 Trouble Shooting With Error Code (OUTDOOR UNIT)

When Discharge temp protection operates 3 times within 40 minutes,

the compressor stops permanently.

Forecast of Cause :

1. Valve is close 2. EEV, Solenoid Valve failure 3. Gas Leak, less 4. Discharge Thermistor failure

5. Outdoor Fan Operation failure 6. Outdoor Heat Exchanger clogged

Check Point 1 : Check if Gas Valve is open

If it is not open, open it and check the operation.

(If Liquid valve close, High pressure error.)

Check Point 3 : Check if gas leak or less gas

Measure Gas pressure, if there is a leak, correct it.

>>If recharging refrigerant, make sure to perform vacuuming and

recharge the specified amount.

Check Point 5 : Check Outdoor FAN, Heat Exchanger

Is there anything obstructing the air distribution circuit?

Is there any clogging of Outdoor Heat Exchanger?

Is the Fan rotating? (Check by hand and if it is locked, replac e the motor)

Check Outdoor Fan Motor

(PARTS INFORMATION 12)

>>If the Fan Motor is defective, replace it.

Check Point 4 : Check Discharge Thermistor 1

Isn’t it fallen off the holder?

Is there a cable pinched?

Check characteristics of thermistor (Refer to Trouble shooting 22),

If defective, replace the thermistor

Check Point 2 : Check EEV, Solenoid Valve and Strainer

Is EEV (EEV2, Indoor unit EEV) open?

(PARTS INFORMATION 5,7)

(PARTS INFORMATION 6)

Is Liquid side Strainer open?

(PARTS INFORMATION 5)

Is Solenoid Valve (SV4 of Main Unit) open?

(PARTS INFORMATION 9)

Is Solenoid Valve (SV4 of Slave Unit) open?

(PARTS INFORMATION 9)

>>If EEV or Solenoid Valve or Strainer is defective, replace it.

Check Point 1 : Check if Liquid Valve is open

If it is not open, open it and check the operation.

(If Gas valve close, High pressure error.)

Check Point 2 : Check if EEV1, SV4 is open

Is EEV (EEV1) open?

If the service tool is connected, check if there is an

indoor unit that is extremely low heat exchanger

temperature.

(On heating, the refrigerant flows to the stopped

indoor unit as well.)

MPa MPa

< Cooling mode >

< Heating mode >

Содержание AB*A12



































































































































































































































































































































Результаты поиска

Содержание AB*A12

Отзывы:

Похожие инструкции для AB*A12

Бренды по названию

Популярные бренды

Fujitsu AB*A12, Руководство по обслуживанию

Результаты поиска

Содержание AB*A12

Отзывы:

Похожие инструкции для AB*A12

Бренды по названию

Популярные бренды