Fujitsu AB*A12 Скачать руководство пользователя

Страница: 146 / 322

Trouble shooting 45

OUTDOOR UNIT Error Method:
Network Communication Error
(Only for Main Unit)

Indicate or Display:

Outdoor Unit : LED1 Flash, LED5

9 Times Blink

Indoor Unit : Operation LED Flash

Timer LED 3 Times Blink

Swing LED 3 Times Blink

ERROR CODE : E : 32

Detective Actuators:

Outdoor Unit Controller PCB circuit

Detective details:

When the network signal from the indoor unit that has a receipt record was not

received longer than 5 minutes. (Indoor Unit does not display Error)

Or, when the network signals from all the Indoor Units were not received for

more than 5 minutes.

Check Point 2 : Check outside cause (Voltage drop or Noise)

Instant voltage drop ------ Check if there is any electric equipment with a large load within the same circuit.

Momentary power failure ----- Check contact failure or leak current in power supply circuit

>> Check Indoor Unit as well.

Check if there is any equipment that causes harmonic wave near the power cable (Neon light bulb or any electronic

equipment which causes harmonic wave). And check the complete insulation of grounding.

>> If the same symptom does not reappear after resetting the power, possibility of noise is high.

Check Point 1 : Check connections

Turn off the power and check/correct followings

Isn’t Outdoor Unit Transmission PCB connection loose?

Check loose or removed communication line between Indoor Unit

and Outdoor Unit.

Make sure Controller PCB for Main Unit has Terminator (CN22).

Check Point 3 : Check Transmission PCB and Controller PCB

When a signal from some Indoor Unit could not be received, check the connection of its Indoor Unit’s Transmission

PCB. (Refer to Trouble Shooting 12)

>> If the symptom does not change, replace Indoor Unit Transmission PCB. (If it still does not improve, replace

Controller PCB.

When the signal from all the Indoor Units could not be received, replace Outdoor Unit Transmission PCB.

>> If the symptom does not change, replace Outdoor Unit Controller PCB.

Outdoor Unit Schematic (CN22:TERMINATOR)

Note : Terminator

Terminator is a resistance that prevents the

reflection of the signal at the end terminal of

the circuit which causes abnormal data

transmission when connecting multiple

devices with 1 piece of cable.

Forecast of Cause :

1. Connection failure 2. Outside cause 3. Transmission PCB failure 4. Controller PCB failure

06-55

Содержание AB*A12



































































































































































































































































































































Результаты поиска

Содержание AB*A12

Отзывы:

Похожие инструкции для AB*A12

Бренды по названию

Популярные бренды

Fujitsu AB*A12, Руководство по обслуживанию

Результаты поиска

Содержание AB*A12

Отзывы:

Похожие инструкции для AB*A12

Бренды по названию

Популярные бренды