FujiFilm FRN001E1E-2U, Брошюра

Страница: 23 / 40

●
F codes: Fundamental Functions
●
E codes: Extension Terminal Functions
Terminal X1 function
Terminal X2 function
Terminal X3 function
Terminal X4 function
Terminal X5 function
Selecting function code data assigns the corresponding function to
terminals [X1] to [X5] as listed below.
0 (1000)
: Select multi-frequency [SS1]
1 (1001) : Select multi-frequency [SS2]
2 (1002) : Select multi-frequency [SS4]
3 (1003) : Select multi-frequency [SS8]
4 (1004) : Select ACC/DEC time [RT1]
6 (1006) : Enable 3-wire operation [HLD]
7 (1007) : Coast to a stop [BX]
8 (1008) : Reset alarm [RST]
9 (1009) : Enable external alarm trip [THR]
10 (1010) : Ready for jogging [JOG]
11 (1011) : Select frequency command 2/1 [Hz2/Hz1]
12 (1012) : Select motor 2/motor 1 [M2/M1]
13 : Enable DC braking [DCBRK]
14 (1014) : Select torque limiter level [TL2/TL1]
17 (1017) : UP (Increase output frequency) [UP]
18 (1018) : DOWN (Decrease output frequency) [DOWN]
19 (1019) : Enable data change with keypad [WE-KP]
20 (1020) : Cancel PID control [Hz/PID]
21 (1021) : Switch normal/inverse operation [IVS]
24 (1024) : Enable communications link via RS-485 or field bus [LE]
25 (1025) : Universal DI [U-DI]
26 (1026) : Enable auto search for idling motor speed at starting [STM]
27 (1027) : Speed feedback control switch [PG/Hz]
30 (1030) : Force to stop [STOP]
33 (1033) : Reset PID integral and differential components [PID-RST]
34 (1034) : Hold PID integral component [PID-HLD]
42 (1042) : Position control limit switch [LS]
43 (1043) : Position control start/reset command [S/R]
44 (1044) : Serial pulse Receive mode [SPRM]
45 (1045) : Position Control return mode [RTN]
46 (1046) : Overload stopping effective command [OLS]
Setting the value of 1000s in parentheses ( ) shown above assigns a negative logic input to a terminal.
Note: In the case of THR and STOP , data (1009) and (1030) are for normal logic, and "9" and "30" are
for negative logic, respectively.
-
-
-
-
-
-
-
-
-
-
Y
Y
Y
Y
Y
0
1
2
7
8
Current Limiter
Electronic Thermal
Overload Protection
for braking resistor
(Mode selection)
(Level)
(Discharging capability)
(Allowable average loss)
0: Disable (No current limiter works.)
1: Enable at constant speed (Disable during ACC/DEC)
2: Enable during ACC/constant speed operation
20 to 200
(The data is interpreted as the rated output current of the inverter for 100%.)
1 to 900 999: Disable
0: Reserved
0.001 to 50.000 0.000: Reserved
2
180
999
0.000
(Limiting Level for driving)
(Limiting Level for braking)
20 to 200 999 : Disable
20 to 200 999 : Disable
Selecting function code data assigns the corresponding function to terminals [Y1], [Y2], and [30A/B/C] as listed below.
0 (1000) : Inverter running [RUN]
1 (1001) : Frequency arrival signal [FAR]
2 (1002) : Frequency detected [FDT]
3 (1003) : Undervoltage detected (Inverter stopped) [LU]
4 (1004) : Torque polarity detected [B/D]
5 (1005) : Inverter output limiting [IOL]
6 (1006) : Auto-restarting after momentary power failure [IPF]
7 (1007) : Motor overload early warning [OL]
10 (1010) : Inverter ready to run [RDY]
21 (1021) : Frequency arrival signal 2 [FAR2]
22 (1022) : Inverter output limiting with delay [IOL2]
26 (1026) : Auto-resetting [TRY]
28 (1028) : Heat sink overheat early warning [OH]
30 (1030) : Service lifetime alarm [LIFE]
33 (1033) : Reference loss detected [REF OFF]
35 (1035) : Inverter output on [RUN2]
36 (1036) : Overload prevention control [OLP]
37 (1037) : Current detected [ID]
38 (1038) : Current detected 2 [ID2]
42 (1042) : PID alarm [PID-ALM]
49 (1049) : Switched to motor 2 [SWM2]
57 (1057) : Brake signal [BRKS]
76 (1076) : PG error signal [PG-ERR]
80 (1080) : Over traveling [OT]
81 (1081) : Time up of the start timer or the end timer [TO]
82 (1082) : Completion of positioning [PSET]
83 (1083) : Current position pulse overflow [POF]
99 (1099) : Alarm output (for any alarm) [ALM]
Setting the value of 1000s in parentheses ( ) shown above assigns a negative logic input to a terminal.
1
1
-
-
-
%
%
-
-
-
Y
Y
Y
Y
Y 999
999
0
7
99
0.01
0.01
Y
Y
10.0
10.0 s
s
0.00 to 3600 Note: Entering 0.00 cancels the acceleration time, requiring external soft-start.
0.00 to 3600 Note: Entering 0.00 cancels the acceleration time, requiring external soft-start.
Acceleration Time 2
Deceleration Time 2
Torque
Limiter 2
Terminal [Y1] Function
Terminal [Y2] Function
Terminal [30A/B/C] Function
Func.
Code
Data
copy *
2
Name Data setting range
Default
setting
Min. Unit
Func.
Code
Data
copy
* 2
Name Data setting range
Default
setting
Min. Unit
-
1
1
0.001
-
%
kWs
kW
Y
Y
Y
Y
*1 When you make settings from the keypad, the incremental unit is restricted by the number of
digits that the LED monitor can display.
(Example) If the setting range is from -200.00 to 200.00, the incremental unit is as follows:
"1" for -200 to -100, "0.1" for -99.9 to -10.0, "0.01" for -9.99 to -0.01, "0.01" for 0.00 to 99.99,
and "0.1" for 100.0 to 200.0
*2 Symbols in the "Data copy" column
Y: Will be copied unconditionally.
Y1: Will not be copied if the rated capacity differs from the source inverter.
Y2: Will not be copied if the rated input voltage differs from the source inverter.
N: Will not be copied.
*3 Reserved for the maker. Do not set any data.
<Changing, validating, and saving function code data when the motor is running>
: Impossible, : Possible (Change data with keys and then
save/validate it with key), : Possible (Change and validate data with
keys and then save it with key)
Function
Settings