Fuji Electric P642 Series Скачать руководство пользователя страница 2

MT6M16534

© Fuji Electric Co., Ltd. All rights reserved.

This Instruction contains the product specifications, characteristics, data, materials, and structures as of

July 2022. The contents are subject to change without notice for specification changes or other reason.

When using a product listed in this Instruction be sure to obtain the latest specifications.

The application examples in this note show the typical examples of using Fuji products and this note

shall neither assure to enforce the industrial property including some other rights nor grant the license.

Although Fuji Electric Co., Ltd. continually strives to enhance product quality and reliability, a small

percentage of semiconductor products may become faulty. When using Fuji Electric semiconductor

products in your equipment, be sure to take adequate safety measures such as redundant, flame-

retardant and fail-safe design in order to prevent a semiconductor product failure from leading to a

physical injury, property damage or other problems.

The product introduced in this Application note is intended for use in the following electronic and

electrical equipment which requires ordinary reliability:

Inverter for Compressor motor or fan motor for Room Air Conditioner

Inverter for Compressor motor for heat pump applications.

If you need to use a semiconductor product in this application note for equipment requiring higher

reliability than normal, such as listed below, be sure to contact Fuji Electric Co., Ltd. to obtain prior

approval. When using these products, take adequate safety measures such as a backup system to

prevent the equipment from malfunctioning when a Fuji

Electric’s product incorporated in the equipment

becomes faulty.

Transportation equipment (mounted on vehicles and ships)

Trunk communications equipment

Traffic-signal control equipment

Gas leakage detectors with an auto-shutoff function

Disaster prevention / security equipment

Safety devices, etc.

Do not use a product in this application note for equipment requiring extremely high reliability

such as:

Space equipment

Airborne equipment

Atomic control equipment

Submarine repeater equipment

Medical equipment

All rights reserved. No part of this application note may be reproduced without permission in writing from

Fuji Electric Co., Ltd.

If you have any question about any portion of this application note, ask Fuji Electric Co., Ltd. or its sales

agencies. Neither Fuji Electric Co., Ltd. nor its agencies shall be liable for any injury or damage caused

by any use of the products not in accordance with instructions set forth herein.

i

Cautions

Содержание P642 Series















Отзывы: