Fromm FS380 Скачать руководство пользователя страница 63

Страница: 63 / 100

Fromm

TRANSPORT-HANDLING-STORAGE

Net weight: 500 kg

WARNING

The machine with low profile base cannot be moved when

assembled.

•

Free the machine from the packaging as shown in the figure.

• Carefully insert the forks of the forklift into the rails

(A)

, marked

with the pictogram

(B)

, to the maximum possible depth.

•

Lift and transfer the machine to the installation location.

WARNING

EXCLUSIVELY USE A FORKLIFT TRUCK OF ADEQUATE CAPACITY TO

LIFT AND TRANSPORT THE MACHINE. USING ANY OTHER SYSTEM

WILL NULLIFY THE WARRANTY FOR ANY DAMAGE CAUSED TO THE

MACHINE.

DANGER

THE RISK OF IMPACT IN ANY CASE REMAINS, CAUSED BY SUDDEN

MOVEMENT DUE TO UNBALANCING OF THE MACHINE PARTS IN THE

EVENT THAT THE BELTS SAG OR SLIP. LIFT THE MACHINE SLOWLY

AND SMOOTHLY (WITHOUT JERKING OR PULSES).

DANGER

ALWAYS CHECK, BEFORE ANY OPERATION, THAT THERE ARE NO

EXPOSED PERSONS IN HAZARDOUS ZONES (IN THIS CASE THE

ENTIRE ZONE SURROUNDING THE PALLETS IS TO BE CONSIDERED

AS A HAZARDOUS ZONE).

To lift the machine, proceed as follows:

• Carefully insert the forks of the forklift into the rails

(A)

, marked

with the pictogram

(B)

, to the maximum possible depth.

•

Lift and transport the machine.

See Picture 35 - pag. 57

Picture 35

Picture 36

Содержание FS380





































































































Результаты поиска

Содержание FS380

Отзывы:

Fromm FS380, Руководство по эксплуатации и обслуживанию, Страница: 63 / 100

Результаты поиска

Содержание FS380

Отзывы: