Froling P2-10 Скачать руководство пользователя страница 18

Страница: 18 / 80

Operating the system

Heating up the boiler

Page 18

B0190806

3.3

Heating up the boiler

3.3.1

Switching on the system

Switch on the main switch on the controls

After the system check by the controls, the system is ready for
operation

3.3.2

Switching on the boiler

All selector switches must be set to “Auto”.

Press the key

The heating system is controlled via the control system according
to the selected mode.

3.3.3

Controlling the boiler

See chapter 4 - Lambdatronic P 3100 control system

3.3.4

Switching off the boiler

Press the key

The boiler follows the shut-down program and switches to
“Burner OFF” status.

The control system then only controls the connected heating
components

3.3.5

Switching off the System

ATTENTION! Only switch off when the boiler has cooled
down.

Switch off the main switch on the controls

The controls are switched off

The system components are powered down.

Caution: The power is still on in the pellet module!

Содержание P2-10

















































































Результаты поиска

Содержание P2-10

Отзывы:

Похожие инструкции для P2-10

Бренды по названию

Популярные бренды

Froling P2-10, Руководство по эксплуатации

Результаты поиска

Содержание P2-10

Отзывы:

Похожие инструкции для P2-10

Бренды по названию

Популярные бренды