Froling P2-10 Скачать руководство пользователя страница 74

Страница: 74 / 80

Installers and service technicians

Parameter list - Lambdatronic P 3100

Page 74

B0190806

Mode: Winter operation

You can select from:

Winter operation
Summer operation
Transitional operation
Firewood operation (EMERGENCY OPERATION)
Cleaning

RBG 3100
Alloc.: 14

Console 3100: possible allocation combinations

Normal: Allocation and control of this heating circuit only

Master: Allocation to respective heating circuit, control of
other heating circuits also possible

Other combinations have no function

Normal

Master

HC1

HC2

HC3

HC4

No allocation

Set day

Set the current date.

Set time

Set the current time.

Restore factory
settings

←

Restores the default settings on the control.
It takes a few seconds for the factory settings to be restored.

Clear error list

←

Deletes all the data saved in the error list.

7.5.3

Error list menu

Up to 25 warnings/errors already eliminated and the respective times
are stored here.

Warning 12/07/01
005 clr. 23:17:24

clr ... cleared:
Error no. 005 was eliminated at this time.

Warning 12/07/01
005 ack. 23:16:23

ack ... acknowledged:
Error no. 005 was acknowledged at this time.

Warning 12/07/01
005 occ. 23:15:18

Remote control 2 error

occ ... occurred:
Error no. 005 occurred at this time.

To display the respective error text press the enter key, e.g.: “Remote
control 2 faulty”.

A list of possible error messages is contained in the chapter on
troubleshooting.

Содержание P2-10

















































































Результаты поиска

Содержание P2-10

Отзывы:

Froling P2-10, Руководство по эксплуатации, Страница: 74 / 80

Результаты поиска

Содержание P2-10

Отзывы: