Froling P2-10 Скачать руководство пользователя страница 13

Страница: 13 / 80

Safety

Safety Devices

Fröling Heizkessel- und Behälterbau Ges.m.b.H, Industriestraße 12, A-4710 Grieskirchen, Austria

Page 13

Tel +43 (0) 7248 606-0 Fax +43 (0) 7248 606-600 [email protected] www.froeling.com

B0190806

2.4

Safety Devices

STOP key

In case of overheating, shut down the
boiler

The pumps continue to run!

Always end heating with the

STOP key. Never use the main
switch.

Key switch (for screw
discharge)

Disengages power from the combustion
unit’s drive components.

CAUTION: The power is still on

in the pellet module!

Main switch

For shutting down the entire system

The power to all components is
switched off.

CAUTION: The power is still on

in the pellet module!

Safety temperature limiter
(STL)

Page 14, Devices for preventing the
boiler from overheating

Fuse

Fuse the controls and electrical
components

When changing fuses, fit fuses with
the rated current specified.

Содержание P2-10

















































































Результаты поиска

Содержание P2-10

Отзывы:

Похожие инструкции для P2-10

Бренды по названию

Популярные бренды

Froling P2-10, Руководство по эксплуатации

Результаты поиска

Содержание P2-10

Отзывы:

Похожие инструкции для P2-10

Бренды по названию

Популярные бренды