Froling P2-10 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 80

Froling P2-10 Скачать руководство пользователя страница 69

Installers and service technicians

Parameter list - Lambdatronic P 3100

Fröling Heizkessel- und Behälterbau Ges.m.b.H, Industriestraße 12, A-4710 Grieskirchen, Austria

Page 69

Tel +43 (0) 7248 606-0 Fax +43 (0) 7248 606-600 [email protected] www.froeling.com

B0190806

7

Oil boiler

...

←

←

←

←

Oil boiler-Storage
temp diff

10°

←

←

←

←

The minimum temperature difference between the oil
boiler and storage tank which releases the oil boiler
loading pump output.

Oil boiler start
delay

60m

←

←

←

←

Delays start of the burner relay if the boiler fails (the
boiler status is off, fault or shut down and the boiler
temp. is 5°C below the target value). In storage mode
the burner relay, however, only comes on when the
storage tank has cooled down. (Top storage temp.
lower than maximum temp. required.)

Oil boiler min.
runtime

5m

←

←

←

←

Minimum runtime for the oil boiler

Oil boiler min.
temp.

50°

←

←

←

←

Oil boiler minimum temperature for release of oil boiler
loading pump or activation of switch valve.

Solar

...

←

←

←

←

Setup Sol Register:

1

←

←

←

←

System-specific parameter: set as per solar diagrams!

Option for systems
0-9

DHW tank target for
solar l.

65°

←

←

←

←

When the specified temperature is reached in the DHW
tank sensor, the DHW tank loading pump switches off.
When using a switch valve, it switches to the heating
element of the storage tank.

Min rev solar pumps 45%

←

←

←

←

Adjusts the minimum speed to the relevant pump type.

Solar ON diff temp

10°

←

←

←

←

The collector loading pump activates when the collector
temperature exceeds the storage or DHW tank
temperature by this value

Solar OFF diff temp

5°

←

←

←

←

The collector loading pump switches off when the
collector temperature exceeds the storage or DHW tank
temperature by this value

Max temp storage
low

85°

←

←

←

←

Maximum bottom storage tank temperature switches
solar loading pump off (unless the excess temperature
protection for the collector activates (135°)). Only in
conjunction with storage tank.

Solar

...

←

←

←

←

Min rev solar pumps 45%

←

←

←

←

Adjusts the minimum speed to the relevant pump type.

In conjunction with
solar heat
exchanger (systems
12,13,14 and 15)

Coll. ON temp. dif.

10°

←

←

←

←

The collector loading pump activates when the collector
temperature exceeds the lower storage or DHW tank
temperature by this value.

Max temp storage
low

85°

←

←

←

←

Maximum bottom storage tank temperature switches
solar loading pump off (unless the excess temperature
protection for the collector activates (135°)).

ON Delay storage
pump

600s

←

ON and OFF delay for the storage-HE-pump relative to
the collector pump

Storage Solar set

60°

←

Top storage tank target value for solar loading

Solar return storage
lo diff

16°

←

Maximum temperature difference between bottom
storage tank temperature or bottom DHW tank
temperature and collector return feed temperature.

«
...
67
68
69
70
71
...
»

Содержание P2-10

















































































Отзывы:

Нет отзывов