Froling P2-10 Скачать руководство пользователя страница 63

Страница: 63 / 80

Installers and service technicians

Initial startup

Fröling Heizkessel- und Behälterbau Ges.m.b.H, Industriestraße 12, A-4710 Grieskirchen, Austria

Page 63

Tel +43 (0) 7248 606-0 Fax +43 (0) 7248 606-600 [email protected] www.froeling.com

B0190806

Drives

Check that drives and servomotors are working

Check the operating speed of the induced draught fan when the
insulating door is closed

under the limit it must operate at 35 - 40%

Adjust using the “MIN Speed” parameter

Check that the door contact switch is working correctly

When the insulating door is open the induced draught fan runs at
100% speed.

Sensors

Check the sensor shown below in the digital input menu:

Sensor

Layout

Description

Door contact

A 0 ... door closed, switch activated
A 1 ... door open, switch not activated

Set the switch point so that the induced
draught fan operates when the
insulating door is open.

Jam sensor

Gravity shaft level sensor (opener):

A 0 ... Sensor covered
A 1 ... Sensor not covered

Jam sensor (closer):

A 0 ... Sensor not covered
A 1 ... Sensor covered

If only screw discharge is used, this
input is used for “Gravity shaft level
sensor”.

The jam sensor is used for suction
systems with screw discharge and is
mounted at the suction piece.

The setting is the same as sensor
“Level MAX”.

Setting sensor “Max level”

Max level

Max level (opener):

A 0 ... Sensor covered
A 1 ... Sensor not covered

Set sensor “Max level”

Combustion
chamber excess
pressure monitor

A 0 ... fault, monitor has been triggered
A 1 ... Combustion chamber pressure OK

Used as opener contact. If the cable is
unplugged from the sensor, the
“Pressure monitor comb chamb” error
message is displayed.

Key switch

(for

screw discharge
only)

Not displayed in menu

When this is activated, the “Key switch
engaged” error message is shown.

Содержание P2-10

















































































Результаты поиска

Содержание P2-10

Отзывы:

Похожие инструкции для P2-10

Бренды по названию

Популярные бренды

Froling P2-10, Руководство по эксплуатации

Результаты поиска

Содержание P2-10

Отзывы:

Похожие инструкции для P2-10

Бренды по названию

Популярные бренды