Froling FHG 20 Скачать руководство пользователя страница 7

Страница: 7 / 62

General information

Froling GmbH, Industriestrasse 12, A-4710 Grieskirchen, Austria

Page 7

www.froling.com

M1060008_US

General information

It is unlawful to carry out modifications to the boiler or to change or

deactivate safety equipment.
In addition to the operating instructions and the applicable national and

local codes and regulations for installation and operation of the boiler

system, all fire, police, and electrical regulations must be observed.

1.1

Installation Hazards

Install, modify and use only in accordance with manufacturer’s manuals.

Refer to authorities having jurisdiction for proper installation. Contact

local building and fire officials about restrictions and installation

inspection in your area. If there are no applicable local codes, follow

ANSI/NFPA 211 and CAN/CSA B365. Special precautions are required

for passing the Chimney through a combustible wall or ceiling.
Inspect and clean exhaust system, Fuel Loading Chamber, Combustion

Chamber, Ash-Pits, and Heat Exchanger frequently in accordance with

owner’s manual.



DANGER!

Working on electrical components may cause severe injuries from electric

shocks!



WARNING!

The electrical system of the boiler shall be supplied from a double 115 V 60

Hz (nominal 230 V AC) 15 amp branch circuit including neutral and ground

connection. For wiring instructions please refer to Section 3.7 in this

Installation Manual!

Chimney must be 6’’ (150 mm) diameter listed UL-103 HT or ULC-S629

residential all-fuel type or tile-lined masonry. Flue connector pipe must be

6’’ (150 mm) diameter made of a minimum 24 MSG black steel.

Inadequate design, installation and maintenance of the flue gas system will

lead to insufficient chimney draft and could result in Danger of Life or

Severe Injury caused by serious faults in combustion, e.g. explosively

combustion of wood gases and flash fires!

This boiler requires fresh air for safe operation and must be installed so

there are provision for adequate combustion and ventilation air!



CAUTION!

Do not connect this unit to a Chimney flue serving another appliance!

Flooring must be a minimum 3/8’’ (10 mm) non-combustible material

covering the installation clearance area! The floor must be level and

reinforced if required. For construction of the floor beneath the boiler please

pay attention to weight of boiler, water content and wood fuel according to

the Installation Manual!

This boiler is not for use with an automatic stoker

Connect to an existing boiler system in combination with heat storage only!

Use original spare parts only. Installation of non-licensed replacement parts

will void the warranty!

Содержание FHG 20































































Результаты поиска

Содержание FHG 20

Отзывы:

Бренды по названию

Популярные бренды

Froling FHG 20, Руководство по установке

Результаты поиска

Содержание FHG 20

Отзывы:

Бренды по названию

Популярные бренды