Froling FHG 20 Скачать руководство пользователя страница 61

Страница: 61 / 62

Boiler Control System Lambdatronic S 3200

Froling GmbH, Industriestrasse 12, A-4710 Grieskirchen, Austria

Page 61

www.froling.com

M1060008_US

5.8.6

System parameters



For changing the current

system parameters

Boiler type – Do not change!

Boiler type

- S4 Turbo 15

Lambda probe installed

YES

S4 Turbo 22/28

Servo-motors installed

YES

S4 Turbo 34/40

Ignition installed *)

S4 Turbo 50/60

Return feed lift pump

Installed *

FHG Turbo 3000 20

Selected

FHG Turbo 3000 30

Return feed mixer installed *)

FHG Turbo 3000 40

FHG Turbo 3000 50

FHG Turbo 3000 70

Do not select

S4 Turbo,

FHG Turbo 3000 70,

Pellet boilers P2,

Pellet boilers P4 or

Turbomatic

Pellet boiler P2 - 10

Pellet boiler P2 - 25

Pellet boiler P4 - 15

Pellet boiler P4 - 38

Turbomatic

Turbomatic 28...55

Turbomatic 70...110

Wood boiler F2 22 / 30

* All marked components not used! Adjust parameter to NO!

Содержание FHG 20































































Результаты поиска

Содержание FHG 20

Отзывы:

Бренды по названию

Популярные бренды

Froling FHG 20, Руководство по установке

Результаты поиска

Содержание FHG 20

Отзывы:

Бренды по названию

Популярные бренды