manualshive.com logo in svg

Fristam Pumps FL2 100, Инструкция по эксплуатации и техническому обслуживанию, Страница: 4 / 40

Поделиться
Скачать
Fristam Pumps FL2 100 Скачать руководство пользователя страница 4

F

riStam

 P

umPS

4

t

echnicaL

 i

nFormation

S

peciFicationS

Maximum Differential Pressure .................................................................... FL2 15 ....145 PSI 
......................................................................................................................FL2 58S.....130 PSI 
......................................................................................................................FL2 58L.....115 PSI 
...............................................................................................FL2 75S, 100S & 130S.....170 PSI 
...............................................................................................FL2 75L, 100L & 130L.....120 PSI
.........................................................................................................FL3 75L & 100L.....115 PSI
Maximum Inlet Pressure ................................................................................................100 PSI 
Temperature Range ................................................................................................ up to 350 °F 

(For temperatures over 200°F contact your local distributor or Fristam for special pump requirements).

m

ateriaLS

 

oF

 c

onStruction

Primary Product Contact Components ..................................................................... AISI 316L 
Cover Gasket .................................................................................................... Viton (standard)

Also Available in ............................................................................................. EPDM

Surface Finish for Product Contact Surfaces ................................................  32 Ra (standard)

S

haFt

 S

eaLS

Seal Types ......................................................................................Single & Double Mechanical 
Recommended Seal Flush Water Pressure (double seal) ............. 

 

1-2 PSI (

5

 PSI maximum) 

Recommended Seal Flush Water Flow Rate (double seal) ......................................... 3-12 gph 
Stationary Seal Ring Material .........................................................................................Carbon

Also Available in ...............................................................................Silicon carbide 

Rotating Seal Ring Material ............................................. Chrome oxide coated stainless steel

Also Available in ...............................................................................Silicon carbide 

O-ring Material ................................................................................................Viton  (standard)

Also Available in ................................................EPDM and other options available

L

ubrication

Oil Grade .................................................................................................................. SAE 15W40 

Oil Capacity - Horizontal 
     Model 15 ....................................................................................0.15 liters (0.04 US gallons) 
     Model  58 ...................................................................................0.25 liters (0.07 US gallons)
     Model  75 ...................................................................................0.60 liters (0.16 US gallons)     
     Model  100 .................................................................................1.80 liters (0.48 US gallons)
     Model  130 ................................................................................ 2.00 liters (0.53 US gallons)
Oil Capacity - Vertical  
     Model  15 ...................................................................................0.15 liters (0.04 US gallons) 
     Model  58 ...................................................................................0.25 liters (0.07 US gallons)
     Model  75 ...................................................................................0.50 liters (0.13 US gallons)
     Model  100 .................................................................................1.30 liters (0.34 US gallons)
     Model  130 .................................................................................1.80 liters (0.48 US gallons)

Содержание FL2 100









































Отзывы:

Нет отзывов