Fristam Pumps FL2 100 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 40

Fristam Pumps FL2 100 Скачать руководство пользователя страница 2

F

riStam

P

umPS

2

D

eScription

This manual contains installation, operation, assembly, disassembly and repair instructions for
the Fristam FL2 15, 58, 75, 100 & 130 models rotary pump and the Fristam FL3 versions of
these models.

Fristam FL2 Series bi-wing rotor pumps are positive-displacement pumps with non-contact
rotors.

Fristam’s FL2 Series bi-wing rotor design combines mechanical simplicity with pumping effi-
ciency. The pump’s bi-wing rotor provides easy maintenance, cleanability, gentle product han-
dling and dependability. With nine pump models and a full range of options, you can match
your process needs precisely.

The FL2 Series pump is available with any connection type desired and may be mounted
with the inlet/outlet connections in a horizontal or vertical orientation. The pump should be
coupled to a motor/drive assembly properly specified to give the desired performance for the
required application.

The FL3 Series pump is a version of the FL2, featuring unique helix-shaped tri-wing rotary
lobes, providing increased suction capabilities and virtually eliminating pulsation and reduc-
ing noise.

!

DANGER:

BEGIN ALL PUMP MAINTENANCE OPERATIONS BY DISCONNECTING
THE ENERGY SOURCE TO THE PUMP. OBSERVE ALL LOCK OUT/TAG
OUT PROCEDURES AS OUTLINED BY ANSI Z244.1-1982 AND OSHA
1910.147 TO PREVENT ACCIDENTAL START-UP AND INJURY.

«
1
2
3
4
...
»

Содержание FL2 100









































Отзывы:

Нет отзывов