Fristam Pumps FL2 100 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 40

Fristam Pumps FL2 100 Скачать руководство пользователя страница 18

F

riStam

P

umPS

18

S

haFt

anD

/

or

b

earing

r

epLacement

Begin all pump maintenance by disconnecting the energy source to the pump.
Observe all lock out/tag out procedures as outlined by ANSI Z244.1-1982 and OSHA
1910.147 to prevent accidental start-up and injury.

t

ooLS

requireD

For

ShaFt

anD

/

or

bearing

repLacement

15

58 L & S

75 L & S

• 10 mm wrench

• 10 mm wrench

• 10 mm wrench

• 5 mm Allen wrench

• 5 mm Allen wrench

• 5 mm Allen wrench

• 10 mm tube for bearings

• 15 - 17 mm tube for

bearings

100 L & S

130 L & S

• 17 mm wrench

• 17 mm wrench

• 6 mm Allen wrench

• 8 mm Allen wrench

• KM12 spanner wrench

Tools for all models:
• Spanner wrench

• Wooden dowel

• Feeler gauges

• Soft-faced hammer

• Flat blade screwdriver

• Indicating torque wrench

• Mild steel rod

• Bearing heater

• Arbor press (beneficial)

g

earbox

D

iSaSSembLy

Remove the oil drain plug and drain the oil.

Remove the coupling key from the drive
shaft.

FL2 15 & 58

: remove guards.

Remove the rear cover bolts from the rear
cover.

Pull the rear cover off the drive shaft exten-
sion. If the cover sticks use a soft-faced
hammer to loosen it.

Remove the rear cover oil seal from the
rear cover and discard.

Remove the rear cover o-ring from the rear
cover and discard.

Straighten the locking tab of the bearing
lock washer. Reinstall the rotors on the
drive and idle shafts. Lock the rotor with a
wood dowel. Remove the lock nut and lock
nut washer from the drive shaft and idle
shaft.

!

Figure 20
for models
FL2 55-100

«
...
16
17
18
19
20
...
»

Содержание FL2 100









































Отзывы:

Нет отзывов