Fristam Pumps FL2 100 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 40

Fristam Pumps FL2 100 Скачать руководство пользователя страница 10

F

riStam

P

umPS

10

Models 58-130: If the rotor nut gasket fails, the threaded hole on the rotor nut and the threads
on the end of the shaft will need to be cleaned. A wire brush is recommended for cleaning
these threads.

L

ubrication

Gearbox

- The oil level should be maintained in the center of the sight glass on the side of the

gearbox housing. The oil should be changed every 4000 hours under normal conditions and
every 2000 hours under severe conditions. See the oil capacity listing in the front.

Elastomers

- Use a food grade lubricant on o-rings and gaskets unless otherwise specified. If

using EPDM o-rings or gaskets, an oil-based lubricant can’t be used.

p

erioDic

m

aintenance

Periodically inspect the pump housing, cover and rotors for any signs of wear or damage. If
wear is present this could be a sign of over pressurization, incorrect rotor gap or bearing wear.

S

eaL

r

epLacement

Begin all pump maintenance by disconnecting the energy source to the pump.
Observe all lock out/tag out procedures as outlined by ANSI Z244.1-1982 and
OSHA 1910.147 to prevent accidental start-up and injury.

t

ooLS

requireD

For

SeaL

repLacement

:

15:

10 mm wrench

100L & S:

19 mm wrench

5 mm Allen wrench

41 mm socket

Flat cover rotor bolt tool

6 mm Allen wrench

(included w/pump)

1” socket for flat cover tool

58L & S:

13 mm wrench

130 L & S:

24 mm wrench

24 mm socket

50 mm socket

6 mm Allen wrench

Flat cover rotor bolt tool

(included w/pump)

1” socket for flat cover tool

75L & S:

17 mm wrench

All Models: Torque wrench

30 mm socket

1/2

” dowel

5 mm Allen wrench

Soft-faced hammer

Flat cover rotor bolt tool

Small flat blade screwdriver

(included w/pump)

Feeler gauges

1” socket for flat cover tool

!

«
...
8
9
10
11
12
...
»

Содержание FL2 100









































Отзывы:

Нет отзывов