Fristam Pumps FL2 100 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 40

Fristam Pumps FL2 100 Скачать руководство пользователя страница 15

FL2 S

erieS

P

umP

15

S

eaL

a

SSembLy

– F

or

D

oubLe

S

eaL

o

nLy

a) Place the seal flush housing face up

on a bench.

b) Lubricate and install the rear sta-

tionary seal o-ring in the bottom of
the stationary seal cavity.

c) Install the rear stationary seal spring

into the stationary recess.

d) Install the rear stationary seals into

the stationary seal cavity and press
into place. Wipe the face of the sta-
tionary seals to remove any dirt or
oil.

e) Fasten the seal flush housing to the front of the

gearbox.

f) Install the seal flush housing o-ring onto the seal

flush housing.

Finish assembling the seal as outlined in the “Seal As-

sembly” section.

S

eaL

a

SSembLy

Note:

when installing the new seal components make

sure that you use all of the components supplied with
thereplacement seal kit. Using some of the old compo-
nents may reduce seal life.
a) With the pump housing lying face down on a table,

lubricate and install the front stationary seal o-ring
in the housing o-ring groove.

b) Place the stationary seal spring into the stationary

seal cavity in the back of the housing (

Figure 14

).

c) Use your thumbs to install the front stationary seal

into the oval shaped stationary seal cavity in the
back of the housing. Wipe the face of the stationary
seals to remove any dirt or oil.

d) Install the rotating seal onto the pump

shaft (

Figure 15

).

Note:

the back of the

rotating seal has a triangular recess that
fits on to the triangular area of the shaft.

Figure 13 Models 58-100 shown

STATIONARY SEAL

O-RING

SPRING

1265000583 Rev -

Figure 14

Figure 15

«
...
13
14
15
16
17
...
»

Содержание FL2 100









































Отзывы:

Нет отзывов