manualshive.com logo in svg

Fristam Pumps FL2 100, Инструкция по эксплуатации и техническому обслуживанию, Страница: 36 / 40

Поделиться
Скачать
Fristam Pumps FL2 100 Скачать руководство пользователя страница 36

F

riStam

 P

umPS

36

t

roubLeShooting

 

p

robLem

  

 

        c

auSe

 

 

 

 

 

S

oLution

Pump not turning 

Interruption of electrical power. 

Reset circuit breaker,   

 

                                                                                                               check fuses. 
 

Keys sheared or missing. 

Replace. 

 

Coupler or belts are not connected. 

Replace or adjust. 

 

Pump shaft or gears sheared. 

Replace. 

 

Wrong rotation. 

Reverse. 

 

Relief valve not properly adjusted. 

Adjust valve.

Pump not priming 

Valve closed in suction line. 

Open valve. 

 

Suction line clogged or restricted. 

Clear suction line. 

 

Air leak in connections or seal. 

Repair leak. 

 

Pump speed too slow. 

Increase speed. 

 

Suction line does not remain flooded.   Install foot valve. 

 

Air lock. 

Bleed suction line. 

 

Excessive clearances in pump. 

Replace out of tolerance  

 

 

                                                                       parts. 

 

NIPA low. 

Increase suction pressure.

Insufficient flow 

Speed too low. 

Adjust speed as required. 

 

Air leak. 

Repair leak.

Noisy operation 

Cavitation. 

Increase NIPA. 

 

Viscous product. 

Slow pump, reduce product. 

 

High vapor pressure, high temp. 

Reduce temperature. 

 

Leaks in piping or pump. 

Repair leaks. 

 

Dissolved gas in product. 

Reduce discharge pressure. 

 

Mechanical noise. 

Check tolerances. 

 

Excessive weight from piping, 

Support piping. 

 

   pump body distorted. 

 

 

Excessive discharge pressure. 

Reduce discharge pressure. 

 

Worn bearing. 

Replace bearing. 

 

Worn gears. 

Replace gears. 

 

Rotor-to-rotor contact. 

Time rotors, replace twisted   

 

                                                                       shafts, replace worn gears.

Pump overloads 

Viscosity of product higher than 

Reduce pump speed, 

 

   expected.                                                    increase piping size.  

 

Higher pressure than expected 

Reduce pump speed, 

 

 

   increase piping size.

Play between gears 

Worn gear teeth. 

Replace gear. 

 

Gear loose on shaft. 

Inspect gear key, keyway and 

 

                                                                      shaft. If all are undamaged,  

 

 

  retighten the gear retaining 

 

 

  nut.  

 

 

Check for backlash.

Содержание FL2 100









































Отзывы:

Нет отзывов