Friedrich Floating Air Pro-Premiere FPHFW18A3A Скачать руководство пользователя страница 44

Страница: 44 / 94

TROUBLESHOOTING

Diagnostic Codes

Outdoor Unit

Diag
Code

Outdoor Failure Description

LED1

LED2

LED3

the root cause my be one of the following

Compressor drive faulted

BLINKS

OFF

BLINKS

a.the outdoor drive board

failed.

b.the compressor

failed.

c. the outdoor control board

failed.

Outdoor fan motor locked rotor
protection

BLINKS

a.the connection of the outdoor fan motor is

loose.

b.there is something blocking the outdoor fan.
c.the fan motor

failed.

d.the outdoor control board

failed.

Outdoor coil anti-overload
protection with cooling

OFF

a.There is too much refrigerant.
b.the outdoor fan motor

failed.

c.the outdoor fan is broken.

d.the condensor is dirty.

e.the air inlet and air outlet of the indoor unit

and the outdoor unit is not normal.

IPM module protection

OFF

BLINKS

OFF

a.The IPM board

failed.

b.The outdoor fan is broken.
c.The outdoor fan motor

failed.

d.The outdoor fan has been blocked.

e.The condenser is dirty.

f.The outdoor unit has been installed without

standard.

PFC protection

BLINKS

OFF

a.the PFC failed.
b.the outdoor drive board failed.

Compressor pre heating process

BLINKS

it is normal mode in cold weather

Chip in outdoor board faulted

OFF

BLINKS

a. Using the wrong drive board.

b. Using the wrong compressor.

AC voltage higher or lower
protection

BLINKS

a.the supply voltage is higher or lower than

normal.

b.the inner supply voltage of the unit is higher

or lower than normal.

DC compressor start failure

BLINKS

OFF

a.the outdoor drive board failed.

b.the compressor failed.

Outdoor ambient temperature too
low protection

BLINKS

OFF

a. Outdoor ambient temperature too low.

Mark description: the lights flash every two seconds for the following faults

Protection against overheated
outdoor radiator

BLINKS

OFF

a. Radiator sensors failed.

b. Detection circuit of the sensor on the control

panel fails

Protection of the system against too

high pressure

BLINKS

OFF

a. The pressure switch fails

b. The pressure detection switch on the control

panel failed.

c. The measured value of the system pressure

exceeds the limit.

Содержание Floating Air Pro-Premiere FPHFW18A3A































































































Результаты поиска

Содержание Floating Air Pro-Premiere FPHFW18A3A

Отзывы:

Похожие инструкции для Floating Air Pro-Premiere FPHFW18A3A

Бренды по названию

Популярные бренды

Friedrich Floating Air Pro-Premiere FPHFW18A3A, Руководство по обслуживанию

Результаты поиска

Содержание Floating Air Pro-Premiere FPHFW18A3A

Отзывы:

Похожие инструкции для Floating Air Pro-Premiere FPHFW18A3A

Бренды по названию

Популярные бренды