Friedrich Floating Air Pro-Premiere FPHFW18A3A Скачать руководство пользователя страница 39

Страница: 39 / 94

INSTALLATION

Checklist and Operation Test

Check Unit following Installation

No.

Items to be checked

Possible malfunction

1 Has the unit been

installed ﬁrmly?

The unit may drop, shake or

emit noise.

Have you done the

refrigerant leakage test?

It may cause insufﬁcient cooling

(heating) capacity

Is heat insulation of

pipeline sufﬁcient?

It may cause condensation and

water dripping.

Is water drained well?

It may cause condensation and

water dripping.

It may cause malfunction or

damage the parts.

Is the voltage of power

supply according to the

voltage marked on the

nameplate?

Is electric wiring and

pipeline installed

correctly?

It may cause malfunction or

damage the parts.

It may cause electric leakage.

Is the unit grounded

securely?

Does the power cord

follow the speciﬁcation?

It may cause malfunction or

damage the parts.

Is there any obstruction

in air inlet and air outlet?

It may cause insufﬁcient cooling

(heating).

It may cause malfunction or

damaging the parts.

The dust and

sundries caused

during installation are

removed?

The gas valve and liquid

valve of connection pipe

are open completely?

It may cause insufﬁcient cooling

(heating) capacity

Test Operation
System Checks

1. Conceal refrigerant pipes where possible.

2. Make sure drain hose slopes downward along entire length at a slope of 1/4”(inch) per ‘(foot).

3. Ensure all refrigerant pipes and connections are properly insulated.

4. Fasten pipes to outside wall, when possible.

5. Seal and weatherproof wall hole which the interconnecting wires and refrigerant pipes pass through.

Perform test operation after completing gas leak and electrical safety check.

1. Turn on electrical disconnect to outdoor unit.

2. Push the “ON/OFF” button on Remote Controller to begin testing or press and hold Emergency ON/OFF button for

5 seconds to force test mode.

3. Push MODE button, select COOLING, HEATING, FAN mode to confirm all functions.

Indoor Unit

1. Do all Remote controller’s buttons function properly?

2. Do the display panel lights work properly?

3. Does the swing louver function properly?

4. Does the drain work?

Outdoor Unit

1. Push the mode button to COOL and adjust the room setting to 61 °F(16°C) deg. wait up to 3 minutes from

compressor time guard. Does compressor and outdoor fan turn on in cooling mode?

2. Push the mode button to HEAT and adjust the room setting to 85 °F(30°C) deg. wait up to 3 minutes for

compressor time guard. Does compressor and outdoor fan turn on in heat mode?

Fig. 438

Содержание Floating Air Pro-Premiere FPHFW18A3A































































































Результаты поиска

Содержание Floating Air Pro-Premiere FPHFW18A3A

Отзывы:

Похожие инструкции для Floating Air Pro-Premiere FPHFW18A3A

Бренды по названию

Популярные бренды

Friedrich Floating Air Pro-Premiere FPHFW18A3A, Руководство по обслуживанию

Результаты поиска

Содержание Floating Air Pro-Premiere FPHFW18A3A

Отзывы:

Похожие инструкции для Floating Air Pro-Premiere FPHFW18A3A

Бренды по названию

Популярные бренды