Friant Tiles Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 25

Friant Tiles Скачать руководство пользователя страница 9

Page 9

Tiles

™

Installation Manual

8-Wire Electrical, Base Power Retro, and Beltline

Power Retro Installation

Frame

Frame

Frame

Self Tapping Screws

Support Bar

Support Bar

Power Retro

Power Retro

Festoon
Bottom Rail

WARNING:

Disconnect power before servicing.

WARNING:

All electrical connections must be fully
engaged and locked. A loose connection
can cause fire and/or electrical shock.

Baseline Power Retro

1. Place Baseline Power Retro over Bot-

tom Rail and line up holes in the Power
Retro mounting bracket with the holes in
the Bottom Rail.

2. Secure with the Self Tapping Screws

provided and tighten securely.

3. Connect Festoon to the Power Retro.

Beltline Power Retro

1. Install Support Bar at the desired height,

and secure with Self Tapping Screws
provided on both sides of the Frame.

2. Place Baseline Power Retro over Support

Bar and line up holes in the Power Retro
mounting bracket with the holes in the
Support Bar.

3. Secure with the Self Tapping Screws

provided and tighten securely.

4. Connect Festoon to the Power Retro.

«
...
7
8
9
10
11
...
»

Содержание Tiles


























Отзывы:

Нет отзывов